what must the tension in each cable be in the diagram in order to order to support the cargo in static equilibrium?

The final answer are current is directly proportional to the potential difference and inversely proportional to the wire's resistance. Therefore, decreasing the resistance of the wire increases the current in the wire.

To increase the current in the wire of an electric current and field investigating setup, the action to be taken is to decrease the resistance of the wire. What is an electric current? The flow of electrons in a conductor is known as an electric current. To complete an electric circuit, the electrons must flow continuously in a circular pattern.

The electron movement is generated by a power supply, such as a battery. Electrons are pushed out of one end of the battery by a voltage differential between the battery terminals (the potential difference). Electrons enter the other end of the battery and complete the circuit.

The potential difference between the battery terminals drives the electrons around the circuit. This generates an electric current. The formula for current is: I = Q/t Where I is the current, Q is the amount of charge transferred, and t is the time taken.

What is the relationship between electric current and fields? When a charged particle moves through a magnetic field, a force is exerted on it. This force is proportional to the particle's velocity, as well as the magnetic field strength and the charge's magnitude.

The mathematical equation that describes this relationship is: F = qvB sinθ Where F is the force on the charged particle, q is the charge, v is the velocity, B is the magnetic field strength, and θ is the angle between the velocity vector and the magnetic field vector.

In the wire, the current is directly proportional to the potential difference and inversely proportional to the wire's resistance. Therefore, decreasing the resistance of the wire increases the current in the wire.

To know more about electric current refer here:

https://brainly.com/question/2264542#

#SPJ11

Magnitude of the acceleration of fan blades will be approximately 165.9 m/s2

The first step is to convert the rotational speed from revolutions per minute (RPM) to radians per second (rad/s), since acceleration is measured in meters per second squared (m/s^2), which is a linear unit of measurement. We can use the conversion factor:

1 revolution = 2π radians

Therefore, 339.0 rev/min is equal to:

339.0 rev/min * (2π rad/1 rev) * (1 min/60 s) = 35.6 rad/s

The acceleration of a point on one of the fan blades can be found using the formula for centripetal acceleration:

a = rω^2

where:

a is the centripetal acceleration

r is the radius of the fan blade (0.13 m)

ω is the angular velocity in radians per second (35.6 rad/s)

Plugging in the values:

a = (0.13 m)(35.6 rad/s)^2

a = 165.9 m/s^2 (rounded to three significant figures)

Therefore, the magnitude of the acceleration of a point on one of the fan blades is 165.9 m/s^2.

learn more about 'rotation':https://brainly.com/question/31276978

#SPJ11

The ratio of the speeds of these bodies is 2.06

The kinetic energy of an object is equal to 1/2mv^2.
For the 4.0 kg body, the kinetic energy is 1/2 (4.0 kg)v^2
For the 8.5 kg body, the kinetic energy is 1/2 (8.5 kg)u^2

Given that the kinetic energy of the 4.0 kg body is twice the kinetic energy of the 8.5 kg body, we can set up the following equation:

1/2 (4.0 kg)v^2 = 2 * (1/2 (8.5 kg)u^2)

Simplifying the equation, we have:

2 (4.0 kg)v^2 = (8.5 kg)u^2

Solving for the ratio of the speeds, we get:

v^2/u^2 = (8.5 kg)/(2 (4.0 kg)) = 4.25

Therefore, the ratio of the speeds of the two bodies is equal to the square root of 4.25, which is approximately equal to 2.06.

So, the 4.0 kg body is moving at approximately 2.06 times the speed of the 8.5 kg body.

To know more about kinetic energy click here:

https://brainly.com/question/999862

#SPJ11

Answer: The force acting on the wire is 0 N

The formula for the force exerted by a magnetic field on a current-carrying wire is F = BIL sin(theta), Where, F = force B = magnetic field strength, I = current, L = length of the wire, Theta = angle between the wire and the magnetic field direction Given that Length of the wire (L) = 35 cm = 0.35 m. Magnetic field strength (B) = 0.53 T

Current through the wire (I) = 4.5 A, We need to find the force acting on the wire (F).The angle between the wire and the magnetic field is 0° as the wire is parallel to the field. Therefore, sin(theta) = sin(0°) = 0° Using the formula, F = BIL sin(theta) F = 0.53 T × 4.5 A × 0.35 m × sin(0°) = 0 N

Therefore, the force acting on the wire is 0 N, as the wire is parallel to the magnetic field direction. It means that the magnetic field does not exert any force on the wire. Note that the force will be non zero if the wire is not parallel to the magnetic field direction.

Know more about  magnetic field here:

https://brainly.com/question/14848188

#SPJ11

Both the ball and the magnet will reach the ground at the same time because the presence of the coil does not affect the rate of free-fall acceleration of the magnet.

This is because, according to the principle of equivalence, objects with different masses fall at the same rate in a vacuum. In this case, the effect of the coil on the magnet is negligible since the magnet's mass is much smaller than that of the Earth. Therefore, both the ball and the magnet will experience the same acceleration due to gravity and reach the ground at the same time, regardless of the presence of the coil.

To know more about magnet, here

brainly.com/question/30437844

#SPJ4

The final speed of the composite object is 0.8 m/s.

We can use the law of conservation of momentum, which states that the total momentum of a closed system remains constant. In this case, the initial momentum of the system is,

initial momentum = (50 kg) x (-5 m/s) + (70 kg) x (5 m/s)

= -250 kg m/s + 350 kg m/s

= 100 kg m/s

Since the carts stick together after the collision, their masses add up to give the mass of the final composite object,

mass of final object = 50 kg + 70 kg

= 120 kg

Using the conservation of momentum, we can solve for the final velocity of the composite object,

initial momentum = final momentum

100 kg m/s = (120 kg) x (v) m/s

Solving for v,

v = 0.83 m/s

Rounding off to one significant figure, velocity is, 0.8 m/s.

To know more about collision, here

brainly.com/question/12117971

#SPJ4

The balloon is being pushed backward by air pressure. When a car begins to move, air pressure builds up in front of the car, pushing air backwards and creating a wind that affects the balloon inside. As the car accelerates, the wind increases, and the balloon is pushed backwards relative to the car. This phenomenon is known as the 'Venturi Effect'.

When a car moves, it creates a pressure difference in front of and behind the car. This difference in pressure creates a force that moves air around the car. In the case of the balloon, the force of the wind created by the car is pushing the balloon backwards. This is the same effect you feel when a fan is turned on, but in reverse.

The Venturi Effect is a phenomenon in fluid dynamics which explains the decrease in pressure when the velocity of the fluid increases. In the case of the balloon, this decrease in pressure created by the wind of the car causes it to move backwards. This is because air is being pushed away from the balloon and the surrounding area, creating a low-pressure environment.

In summary, the balloon is being pushed backwards by air pressure as the car moves forward. This is known as the Venturi Effect, and it is caused by the decrease in pressure caused by the wind of the car.

For more similar questions on" balloon"

brainly.com/question/30457768

#SPJ11

The magnetic field strength is 86mT and if the maximum diameter of the electron orbit before the electron hits the wall of the tube is 2.5 cm, then the maximum electron kinetic energy is 1.6 x 10^(-14) J.

a. To determine the magnetic field strength, we can use the equation for the electron cyclotron frequency:

f = (eB)/(2πm),

where e is the charge of the electron (1.6 x 10^-19 C),

m is the mass of the electron (9.11 x 10^-31 kg), and

f is the frequency (2.4 GHz).

First, convert the frequency to Hz:

2.4 GHz = 2.4 x 10^9 Hz.

Next, rearrange the equation to solve for B:

B = (2πmf)/e

Finally, plug in the values and calculate B:

B = (2π * (9.11 x 10^-31 kg) * (2.4 x 10^9 Hz))/(1.6 x 10^-19 C)

B = 86mT

So, the magnetic field strength is 86mT.

b. To find the maximum electron kinetic energy, we first need to determine the maximum electron velocity, using the maximum diameter of the electron orbit (2.5 cm) and the cyclotron frequency.

The circumference of the orbit is

C = πd

= π * (2.5 x 10^-2 m).

The time for one orbit is

T = 1/f

= 1/(2.4 x 10^9 Hz).

Now, find the electron's maximum velocity:

v = C/T

= (π * (2.5 x 10^-2 m))/(1/(2.4 x 10^9 Hz))

= 1.884 x 10^8 m/s.

Finally, use the equation for kinetic energy to find the maximum electron kinetic energy:

K = 0.5mv^2

= 0.5 * (9.11 x 10^-31 kg) * (1.884 x 10^8 m/s)^2

= 1.6 x 10^-14 J.

So, the maximum electron kinetic energy is 1.6 x 10^-14 J.

Learn more about kinetic energy:

https://brainly.com/question/25959744

#SPJ11

If the balls have a head-on, inelastic collision and the 2.0-kg ball recoils with a speed of 3.2 m/s, the kinetic energy lost in the collision is 364.6 J.

Using conservation of momentum, we can find the final velocity:

m1 * v1 + m2 * v2 = (m1 + m2) * vf

Solving for vf, we get:

vf = (m1 * v1 + m2 * v2) / (m1 + m2)

= (2.0 kg * 14 m/s + 6.3 kg * 4.0 m/s) / (2.0 kg + 6.3 kg)

= 6.0 m/s

The final total kinetic energy of the system is:

KEf = (1/2) * (m1 + m2) * vf^2

= (1/2) * 8.3 kg * (6.0 m/s)^2

= 112.2 J

The kinetic energy lost in the collision is the difference between the initial and final kinetic energies:

KE lost = KEi - KEf

= 476.8 J - 112.2 J

= 364.6 J

An inelastic collision is a type of collision between two or more objects in which the total kinetic energy of the system is not conserved. In an inelastic collision, some or all of the kinetic energy of the colliding objects is converted into other forms of energy such as heat, sound, or deformation of the objects.

In an inelastic collision, the colliding objects stick together after the collision and move with a common velocity. This is in contrast to an elastic collision, in which the colliding objects bounce off each other and the total kinetic energy of the system is conserved. Inelastic collisions can occur in many different situations, such as in car crashes, when two objects collide and stick together, or when a ball hits a wall and loses some of its kinetic energy due to deformation.

To learn more about Inelastic collision visit here:

brainly.com/question/15742157

#SPJ4

Complete Question: -

Two balls with masses of 2.0 kg and 6.3 kg travel toward each other at speeds of 14 m/s and 4.0 m/s, respectively. If the balls have a head-on, inelastic collision and the 2.0-kg ball recoils with a speed of 3.2 m/s, how much kinetic energy is lost in the collision?

The laws of physics that can be used to explain the behaviors of the carts in this interactive, whether or not the collision was elastic or inelastic, are the laws of conservation of momentum and conservation of energy.

The law of conservation of momentum states that the total momentum of the objects before the collision is equal to the total momentum of the objects after the collision.

The law of conservation of energy states that the total energy of the system remains constant, regardless of the type of collision that takes place.

If the collision is elastic, then the total kinetic energy of the objects before and after the collision is equal. If the collision is inelastic, then the total kinetic energy of the objects after the collision is less than before the collision.

This law applies to both elastic and inelastic collisions. Conservation of energy also applies to both elastic and inelastic collisions. In elastic collisions, the kinetic energy is conserved.

Learn more about the Laws of conservation of momentum here:

https://brainly.com/question/7538238

#SPJ11

The magnetic flux through the loop is 0.125 Wb when oriented perpendicular to the magnetic field, 0.0625 Wb when oriented 60.0° from the magnetic field, and 0 Wb when oriented parallel to the magnetic field.

To calculate the magnetic flux through the loop, we can use the formula:
Magnetic flux (Φ) = B × A × cosθ
where B is the magnetic field magnitude, A is the area of the square loop, and θ is the angle between the magnetic field and the loop's normal vector.
a. Perpendicular to the magnetic field (θ = 0°)
In this case, cosθ = cos(0°) = 1.
Area (A) = (side length)² = (0.250 m)² = 0.0625 m²
Φ = B × A × cosθ = 2.00 T × 0.0625 m² × 1 = 0.125 Wb
b. 60.0° from the magnetic field (θ = 60°)
In this case, cosθ = cos(60°) = 0.5.
Φ = B × A × cosθ = 2.00 T × 0.0625 m² × 0.5 = 0.0625 Wb
c. Parallel to the magnetic field (θ = 90°)
In this case, cosθ = cos(90°) = 0.
Φ = B × A × cosθ = 2.00 T × 0.0625 m² × 0 = 0 Wb

For more such questions on magnetic field

brainly.com/question/26257705

#SPJ11

A decrease in charge, q, will result in a decrease in the electric field strength. The ratio of the final to initial field strengths can be expressed as qf/qi. If q is halved, the ratio would be 0.5. If the radius, r, is halved, the ratio would be 1/2r2i/r2i, which is equal to 0.25. If r is halved, but the distance remains the same, the ratio would be 1/2r2i/r2i, which is equal to 0.25.

The electric field strength is inversely proportional to the distance from the charge, and directly proportional to the charge and the radius of the sphere. Therefore, halving the charge or radius will result in a decrease in the electric field strength. Halving the radius, with the distance remaining the same, will result in the same ratio as halving the charge because the distance will be the same in both cases.

Know more about electric field here

https://brainly.com/question/8971780#

#SPJ11

The probability that the passenger will get on the first train that arrives is the same as the probability that they will arrive at the station between 7 and 8 a.m., which is 1/2.

The uniform distribution is a type of probability distribution where all outcomes are equally likely. In this case, the passenger arrives at the station at a time that is uniformly distributed between 7 and 8 a.m. Therefore, the probability that the passenger will get on the first train that arrives is the same as the probability that they will arrive at the station between 7 and 8 a.m., which is 1/2.
In other words, the probability that the passenger will go to destination A is 1/2. This is because the probability that they will arrive between 7 and 8 a.m. and get on the first train that arrives is the same as the probability that they will arrive between 7 and 8 a.m., which is 1/2.

Therefore, the proportion of time the passenger goes to destination A is 1/2. This is because the probability of them getting on the first train that arrives is the same as the probability of them arriving between 7 and 8 a.m., which is 1/2.

For more such questions on Probability distribution.

https://brainly.com/question/14210034#

#SPJ11

Answer:

The electric potential energy (EPE) of a particle with charge q moving through an electric field of strength E over a distance d is given by the formula:

EPE = qEd

In this problem, we are given:

EPE = 5.2 x 10^-18 J

E = 80 N/C

d = 12 m

Substituting these values into the formula, we get:

5.2 x 10^-18 J = q(80 N/C)(12 m)

q = 5.2 x 10^-18 J / (80 N/C)(12 m)

q = 6.875 x 10^-21 C

Therefore, the particle charge is 6.875 x 10^-21 Coulombs.

Explanation:

BRAINLIEST PLEASE!

Answer:

The answer to your problem is, the spring constant K should be 6 N/m.

Explanation:

When the force F should be applied at the spring so it generated the stretching distance

i.e.

F = k.x

F means the force

K means the constant

x means the stretching distance

Here the weight should be 96 N, the stretching distance is 16 km

Now the spring constant should be:

K = f/x

= 96/16

= 6 N/m

Thus the answer to your problem is, the spring constant K should be 6 N/m.

When a ball is thrown at an upward angle, the vertical and horizontal components of velocity change in different ways. The vertical component of velocity decreases to a certain point before increasing again due to gravity. However, the horizontal component of velocity remains constant throughout the motion of the ball.

When a ball is tossed at an upward angle, the velocity has two components; vertical and horizontal components. The horizontal component is unaffected since there is no force acting on it.

The vertical component is influenced by the gravitational force acting on the ball. As the ball goes up, the vertical component of velocity decreases to zero. The maximum point is reached when the ball's velocity is zero. At this point, the ball stops going up and starts going down. As the ball falls, the vertical component of velocity increases in the opposite direction to the gravitational force acting on it.

Therefore, the vertical component of velocity changes as the ball is tossed at an upward angle. It increases, then decreases to zero at the top of its trajectory, and then increases again as the ball falls back to the ground. The horizontal component of velocity is constant throughout the motion of the ball because there is no force acting on it.

Hence, when a ball is tossed at an upward angle, the vertical and horizontal components of velocity change in different ways.

To know more about the components of velocity, refer here:

https://brainly.com/question/14431896#

#SPJ11

The transit technique used to identify planets involves looking for small dips in a star's brightness as a planet crosses in front of it. This causes a slight decrease in the amount of light received by the Earth from that star, which is then detected by astronomers.

Transit method is a technique that uses the detection of planetary transits to identify exoplanets. By detecting dips in the brightness of a star, caused by a planet crossing in front of it, this method allows for the detection of planets orbiting other stars beyond our own solar system.

To find exoplanets, astronomers look for periodic dips in the brightness of stars that are caused by a planet passing in front of them. The amount of light that a planet blocks depends on its size, so larger planets create deeper dips in the star's brightness.

The timing and duration of the dips also provide information about the planet's orbit, size, and composition.

Transiting planets are therefore more likely to be detected if they have a large radius compared to their host stars, or if their orbital periods are short.

The transit method is also more effective when the host star is relatively small and bright, as this makes the planet's transit easier to detect.

To know more about transit technique, refer here:

https://brainly.com/question/12484173#

#SPJ11

On the screen, 200 cm behind the slits, the fringe spacing will be 8 mm.

Due to its dependence on L, the spacings between various fringes get smaller as the distance between the slits gets more. The space between various fringes grows as the light's wavelength rises because this is a wavelength-dependent property.

The equation: gives the screen's fringe spacing in a double-slit experiment.

dsin(theta) = mlambda

The fringe spacing will therefore double if the screen distance is increased from 100 cm to 200 cm.

The new fringe spacing will be as follows:

2 * 4 mm = 8 mm

To know more about wavelength visit:-

https://brainly.com/question/13533093

#SPJ1

Unusual circumstances caused Kepler to become a lawyer in his 40s'. Johannes Kepler was forced to switch professions due to a lack of funds. Johannes Kepler was unable to pay his bills by working as a mathematician and scientist alone.

As a result, in his forties, Kepler began studying law to make ends meet. Kepler was assigned to be an adviser to the Emperor Ferdinand's chancellor due to his success in the scientific field, and it was there that he learned the importance of the law.

Kepler became a professor of mathematics at the University of Graz in Austria in 1594, and he held this position for eleven years before being expelled for theological reasons.

He later moved to Prague, where he was appointed the mathematician to Rudolf II, the Holy Roman Emperor, and remained in that position until Rudolf's death in 1612.2.

Meaning of expand:

Expand means to make or become larger or more extensive. It also means to write out or present in more detail. It also means to spread out, stretch out, or unfold.

To learn more about Kepler:

https://brainly.com/question/1608361#
#SPJ11

The relative permittivity of a dielectric medium is a measure of the electric field created within it when exposed to an electromagnetic wave. The relative permittivity is calculated by comparing the electric field in the dielectric medium to the electric field in a vacuum.

In a dielectric medium, the electric field is weakened due to the presence of molecules that absorb some of the energy from the electromagnetic wave. The greater the number of molecules, the higher the relative permittivity of the dielectric medium. The lower the relative permittivity of a dielectric medium, the faster the speed of the electromagnetic wave traveling through it.

In conclusion, the relative permittivity of the dielectric medium in which the electromagnetic wave is traveling can be used to measure the electric field within it. The greater the number of molecules present in the dielectric medium, the higher the relative permittivity and the slower the speed of the electromagnetic wave.

To know more about relative permittivity refer here:

https://brainly.com/question/29288724#

#SPJ11

When a parcel of air rises without any external forces ,the temperature decreases so it expands because there's less pressure higher up in the atmosphere.

The temperature decreases because

To learn more about the parcel of air:

https://brainly.com/question/30580488.

#SPJ11

The inductance of a coil, if the coil produces an emf of 2.50 V when the current in it changes from -29.0 mA to 33.0 mA in 14.0 ms, is 0.146 H.

Inductance of a coil The amount of electromotive force generated across a conductor when there is a change in the current flowing through it is defined as self-inductance.

The unit of inductance is the Henry (H), with the symbol L. The voltage induced in the coil is determined by the current passing through it, as well as the coil's inductance. Faraday's law of electromagnetic induction establishes a link between the two entities.

The principle of electromagnetic induction is defined by Faraday's law, which states that the emf (electromotive force) produced by a change in magnetic flux linkage with time is proportional to the negative of the rate of change of magnetic flux linkage.

When there is a change in magnetic flux passing through a coil, this law predicts that an electromotive force is generated in it.

The acronym emf stands for electromotive force, and it represents the quantity of energy that drives current flow in a circuit. The unit of emf is the volt (V).

The amount of electromotive force generated across a conductor when there is a change in the current flowing through it is defined as self-inductance.

The unit of inductance is the henry (H), with the symbol L.

The inductance of a coil is given by the formula: L = E/(di/dt)

Where L is the inductance of a coil E is the voltage induced in the coil di/dt is the rate of change of current passing through the coil.

Thus, the inductance of a coil, if the coil produces an emf of 2.50 V when the current in it changes from -29.0 mA to 33.0 mA in 14.0 ms, is 0.146 H.

To know more about  inductance of a coil refer here:

https://brainly.com/question/31388862#

#SPJ11

To explain to Jacob how the number of field lines and the magnitude of the charge are related, Imad should mention that the number of field lines is proportional to the magnitude of the charge.

There is a relationship between the number of field lines and the magnitude of the charge. The magnitude of the charge is directly proportional to the number of field lines that pass through the surface that is perpendicular to the field lines. The number of field lines created by a charge or charges is proportional to the charge or charges' magnitude.

In the absence of any other charges or objects, the field lines emanating from a charge with magnitude q will terminate on another charge with magnitude q of opposite polarity, according to Coulomb's law. Therefore, Jacob should be told that the number of field lines is proportional to the magnitude of the charge, meaning that if the charge's magnitude increases, the number of field lines will increase as well.

Learn more about Coulomb's law at:

https://brainly.com/question/506926

#SPJ11

The velocity at impact will be (-10) m/s if all forces acting on the spacecraft (weight, drag, and thrust) are included.

To find the velocity at impact, first, we need to consider all the forces acting on the spacecraft (weight, drag, and thrust). Then, we can use these forces to find the net force and acceleration. Finally, we can calculate the impact velocity.

Step 1: Calculate the weight of the spacecraft:-
Weight = mass × gravitational acceleration
Weight = 2060 kg × 3.7 m/s² = 7618 N

Step 2: Calculate the net force acting on the spacecraft:-
Net force = thrust - drag - weight
Net force = 4810 N - 7500 N - 7618 N = -10308 N

Step 3: Calculate the acceleration of the spacecraft:-
Acceleration = net force/mass
Acceleration = -10308 N / 2060 kg = -5 m/s²

Step 4: Calculate the velocity at impact:-
We know that the initial velocity is 40 m/s, and the propellant burns for 10 seconds. We can use the equation of motion (v = u + at) to find the final velocity:-
Final velocity(v) = initial velocity(u) + acceleration(a) × time(t)
Final velocity = 40 m/s + (-5 m/s²) × 10 s = 40 m/s - 50 m/s = -10 m/s

Therefore, the velocity at impact will be -10 m/s (the negative sign indicates that the velocity is in the opposite direction to the initial velocity).

Learn more about thrust: https://brainly.com/question/742835

#SPJ11

The electrostatic force between two protons separated by a distance of 1.0 × 10^-6 m is 2.3 × 10^-8 N.

Electrostatic force is the force between two electrically charged objects. This force can either be attractive or repulsive.

It is proportional to the product of the two charges and inversely proportional to the square of the distance between them.

The force is defined by Coulomb's law which states that:

The electrostatic force between two point charges is directly proportional to the product of the charges and inversely proportional to the square of the distance between them.

The formula for Coulomb's law is given as:F = kq1q2/r2

WhereF is the electrostatic forcek is Coulomb's constantq1 and q2 are the charges of the two particles is the distance between the two particles in meters.

The value of Coulomb's constant is 9.0 × 10^9 Nm^2/C^2.Let's consider two protons separated by a distance of 1.0 × 10^-6 m. The charge on each proton is +1.6 × 10^-19 C.

F = kq1q2/r2F = (9.0 × 10^9 Nm^2/C^2)(+1.6 × 10^-19 C)(+1.6 × 10^-19 C)/(1.0 × 10^-6 m)^2F = 2.3 × 10^-8 N

To know more about electrostatic force refer here:

https://brainly.com/question/9774180#

#SPJ11

A diffraction grating that has 130 lines per centimeter for 580 nm light, if the screens are 1.50 m apart, then the distance between the edges is 30.6 mm

The formula for the distance between fringes for a diffraction grating is given:

d sinθ = mλ,

where d is the spacing between the grating lines, θ is the angle between the incident beam and the diffracted beam, m is the order of the diffraction maximum, and λ is the wavelength of light.

It can also be expressed as

Δy = mλD/d,

where Δy is the distance between adjacent fringes on the screen, D is the distance from the grating to the screen, and d is the spacing between the grating lines.

Given data:

Spacing between grating lines, d = 1/130 cm = 0.00769 cm

The wavelength of light, λ = 580 nm = 580 × 10⁻⁹ m

Distance from grating to the screen, D = 1.50 m

The formula to calculate the distance between fringes produced by a diffraction grating is given:

Δy = mλD/d

Now, substituting the given values in the above formula we get,

Δy = (1)(580 × 10⁻⁹ m)(1.50 m)/(0.00769 × 10⁻⁴ m)

Δy = 0.0306 m = 30.6 mm

Therefore, the distance between fringes produced by a diffraction grating having 130 lines per centimeter for 580 nm light, if the screen is 1.50 m away is 30.6 mm.

Learn more about diffraction grating at https://brainly.com/question/13104464

#SPJ11

At the point when an atom gains/loses an electron, the atom becomes charged and is called an ion.

Acquiring an electron brings about a negative charge, so the atom is an anion.

Losing an electron brings about a positive charge, so an atom particle is a cation.

An atom is a nonpartisan molecule that contains an equivalent number of protons and electrons. A particle is an atom that has lost or acquired at least one electron and has a positive or negative charge subsequently. In this way, the principal contrast between an atom and a particle is that an atom has an impartial charge while a particle has a positive or negative charge.

A few instances of ions include:

Chloride anions (Cl - )

Sulfate anions (SO 42-)

Nitrate anions (NO 3-)

Calcium cation (Ca 2+)

Manganese (II) cation (Mn 2+)

Hypochlorite anion (ClO - )

Ammonium cation (NH 4+)

Ferric cation (Fe 3+)

to know more about the electron click here:

https://brainly.com/question/28337734

#SPJ4

The orbital speed of the planet is [tex]4.41 * 10^3 m/s[/tex] and the orbital period of the planet is 22.608s when its mass is [tex]3.5 * 10^{31}kg.[/tex]

The mass of the planet (m) = [tex]3.5 * 10^{31}kg[/tex]

The distance of star from the planet (r) = [tex]1.2 * 10^{11}m[/tex]

The planet is moving in circular shape around the star.

The orbital speed of the planet = v

The orbital speed of the planet can be calculated using the equation for the orbital speed, which is given by [tex]v = \sqrt{(GM/r)}[/tex], where G is the gravitational constant = [tex]6.67 * 10^{-11} m^3/(kg*s^2)[/tex]

[tex]v = \sqrt{6.67 * 10^{-11} m^3/(kg*s^2) * 3.5 * 10^{31}kg/1.2 * 10^{11}m}[/tex]

[tex]v = \sqrt{23.345 * 10^{20}/1.2 * 10^{11}} = \sqrt{19.45 * 10^9}[/tex]

[tex]v = 4.41 * 10^3 m/s[/tex]

the orbital speed of the planet is = [tex]4.41 * 10^3 m/s[/tex]

The orbital time period of the planet can be calculated using the equation for the orbital period, which is given by [tex]T = 2 * \pi * \sqrt{(r^3/GM)}[/tex]

[tex]T = 2 * \pi * \sqrt{(1.2 * 10^{11})^3/6.67 * 10^{-11} m^3/(kg*s^2) * 3.5 * 10^{31}kg}[/tex]

[tex]T = 2 * \pi * \sqrt{(1.2 * 10^{11})^3/23.345 * 10^{20}}[/tex]

[tex]T = 2 * \pi * \sqrt{0.07 * 10^{13}}[/tex]

[tex]T = 2 * \pi * 0.26 * 3.9[/tex]

T = 22.608s

Hence the orbital period of the planet is 22.608s

To learn more about speed click here https://brainly.com/question/28224010

#SPJ1

If there is no change in the charge distributions, the direction of the net electrostatic force on an electron located at the center of the circle would be zero.

The electric field is a force that acts on a charged particle in an electric field. The electric field exerts a force on a charged particle that is proportional to the charge on the particle and the strength of the electric field.The force is exerted in the direction of the electric field. If an electron is placed in the electric field, it will experience a force in the opposite direction to the electric field.

When a charged particle is placed in a uniform electric field, the net electrostatic force on the particle is zero, as the direction of the force is opposite to the direction of the electric field.This can be understood through the principle of superposition. Since there is no change in the charge distribution, the electric field at the center of the circle will be zero. Therefore, the net electrostatic force on an electron located at the center of the circle will be zero.

Learn more about electric field at:

https://brainly.com/question/28347684

#SPJ11