The best additive to use to try to minimize the whining noise in a 1956 Chevy Powerglide transmission is Automatic Transmission Additive.
There are many reasons why Automatic Transmission Additive is the best additive to use to try to minimize the whining noise in a 1956 Chevy Powerglide transmission, including but not limited to:ATFs (automatic transmission fluids) are low viscosity lubricants that are formulated to protect automatic transmissions and provide smooth shifting. ATFs, however, have a variety of drawbacks. For example, they can foam, oxidize, shear, and run too hot, all of which can contribute to transmission noise, slipping, and poor shifting.Automatic transmission additives, on the other hand, have been designed to overcome these limitations by incorporating special friction modifiers, anti-wear agents, and seal conditioners, among other ingredients. These additives can reduce friction and wear in the transmission, which can help to quiet down noise and reduce vibration.
Learn more about Automatic Transmission Additive: https://brainly.com/question/14646065
#SPJ11
2+2 = 234
T or F
This is a very big engineering question.
does the combined heat transfer coefficient offer the convenience of incorporating the effects of radiation in the convection heat transfer coefficient, and to ignore radiation in heat transfer calculations?
Yes, the combined heat transfer coefficient does offer the convenience of incorporating the effects of radiation in the convection heat transfer coefficient. In heat transfer calculations, radiation can be ignored and only the convection component of heat transfer needs to be considered. This is due to the fact that the combined heat transfer coefficient combines the convection and radiation components into a single coefficient.
The combined heat transfer coefficient is a function of the thermal conductivity, the Stefan-Boltzmann constant, and the view factor. This view factor is a measure of how much of the radiation from one surface is intercepted by the other surface. The higher the view factor, the more radiation will be transferred between the two surfaces. By incorporating this view factor into the combined heat transfer coefficient, the effects of radiation in the heat transfer calculation can be taken into account.
In conclusion, the combined heat transfer coefficient offers the convenience of incorporating the effects of radiation in the convection heat transfer coefficient, and to ignore radiation in heat transfer calculations.
for more such questions on heat transfer coefficient.
https://brainly.com/question/29745276
#SPJ11
You are travelling along a four lane highway. You see an emergency vehicle pulled over with its lights flashing ahead. Which of the following is true?A You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 20 mphB You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 30 mphC You must come to a complete stop regardless of which direction you are travelling
You are required to leave an empty lane between your car and the emergency vehicle if it is safe, otherwise reduce speed by 20 mph is true.
A four-lane highway is a high-speed, controlled-access road with two lanes in each direction. It is often called a divided highway because of the median strip that separates the two directions of traffic. It is the most common type of multi-lane highway in the United States.
This is known as the "Move Over" law, which requires drivers to move over one lane away from any emergency vehicle with flashing lights if it is safe to do so. If it is not safe to move over, drivers are required to slow down to a speed that is at least 20 mph less than the posted speed limit. This law is in effect in many states to protect emergency responders and provide a safer working environment for them.
To learn more about speed-limit:
https://brainly.com/question/28488266
#SPJ11
building envelope, sometimes also called thermal envelope or building enclosure, controls the flows of between the interior and exterior of the building?
The building envelope is an essential component of any structure, providing a protective barrier between the interior and exterior of the building. By controlling the flow of air, moisture, and heat, the building envelope ensures the indoor air quality and energy efficiency of the building.
The components of the building envelope include the walls, roofs, windows, doors, and foundation of the building, as well as insulation and other materials. The primary purpose of the building envelope is to provide a protective barrier against the elements, ensuring the interior of the building is insulated from the outside climate. The building envelope also helps to maintain indoor air quality, as it reduces the amount of air infiltration from outside. In addition, the building envelope increases the efficiency of the building’s heating and cooling systems, reducing energy consumption and costs.
In order to maintain its protective barrier, the building envelope must be constructed with durable and weather-resistant materials. Additionally, the building envelope should be properly sealed to reduce air leakage. Windows and doors should be designed to minimize the risk of water infiltration, while insulation should be installed to reduce heat transfer.
You can learn more about building envelopes at: brainly.com/question/28163927
#SPJ11
why must you consider output impedance of signal conditioning circuit or input impedance of measuring device
It is important to consider the output impedance of a signal conditioning circuit and the input impedance of the measuring device for several reasons. First, the signal conditioner’s output impedance will affect the amplitude and frequency response of the signal as it is sent to the measurement device.
1) If the impedance of the signal conditioner and the measuring device don't match, it can lead to incorrect readings.
2) Secondly, the signal conditioner’s output impedance also affects the signal-to-noise ratio, which can influence the quality of the measurements taken.
3) Lastly, the input impedance of the measuring device must match the output impedance of the signal conditioning circuit in order to ensure a low-distortion signal that accurately reflects the original signal.
In summary, it is important to consider the output impedance of the signal conditioning circuit and the input impedance of the measuring device in order to ensure accurate and high-quality measurements.
It is important to consider the output impedance of a signal conditioning circuit or the input impedance of a measuring device for optimal performance and accurate measurements. This is because the impedance values affect the signal transfer between the circuit and the device.
The input impedance of a measuring device refers to the resistance of the device input to the output impedance of the signal conditioning circuit.
If the input impedance of the device is too low, it can lead to a large current flowing from the circuit to the device, which can cause distortion and reduce the accuracy of the measurement.
On the other hand, if the input impedance is too high, it can affect the signal transfer between the circuit and the device, leading to a loss of signal strength and distortion.
For more such questions on impedance
https://brainly.com/question/29853108
#SPJ11
what should motorcyclists do to protect themselves while riding?
Explanation:
Wear protective leathers/pads and a helmet. Stay visible....don't ride in blind spots of other drivers. Don't speed or weave in and out of traffic. Use turn signals and headlight/taillight. Make sure your 'cycle is in good working order / maintained properly. Do not drink and ride. Avoid bad weather and winter weather. Ride defensively. Use your mirrors. Swivel your head ....be aware of your traffic surroundings. Take a rider safety course. Learn how to ride the bike you are on in a safe place ...etc etc
When E = 14 V and R = 1 Ω, the current is _________ amperes.
When E = 14 V and R = 4 Ω, the current is _________ amperes.
When E = 14 V and R = 8 Ω, the current is _________ amperes.
When E = 14 V and R = 12 Ω, the current is _________ amperes.
Answer:
When E = 14 V and R = 1 Ω, the current is 14 A.
When E = 14 V and R = 4 Ω, the current is 3.5 A.
When E = 14 V and R = 8 Ω, the current is 1.75 A.
When E = 14 V and R = 12 Ω, the current is 1.166... A
(rounded to three decimal places).
Explanation:
To calculate the current (I) using Ohm's law, we can use the formula:
I = E / R
where I is the current in amperes (A), E is the voltage in volts (V), and R is the resistance in ohms (Ω).
Answer:
Current = Emf / Resistance
When E = 14 V and R = 1 Ω, the current is 14/1 amperes = 14 amp
When E = 14 V and R = 4 Ω, the current is 14/4 amperes = 3.5 amp
When E = 14 V and R = 8 Ω, the current is 14 / 8 amperes = 1.75 amp
When E = 14 V and R = 12 Ω, the current is 14 / 12 amperes = 1.16 amp
what is the transfer function? what is the steady-state error, ess? what is the natural frequency? you can assume ra
The transfer function is a mathematical representation of the relationship between the input and the output of a system. The steady-state error, or ess, is the difference between the desired output and the actual output when the system reaches a steady state. The natural frequency is the frequency of the system's response without any external forces.
Transfer Function: Transfer Function is used in signal processing, control engineering, and other disciplines that deal with systems or signals. The ratio of output to input in Laplace transform is known as the transfer function.
Steady-State Error: The error that happens when the system is at a stable state is referred to as a steady-state error. The difference between the desired and actual response is known as steady-state error. A system's ability to track a specific input as time progresses is characterized by this kind of error. If the input signal is a unit step, then the steady-state error is referred to as the static error coefficient. The coefficient of the steady-state error is frequently used to classify systems in control engineering.
Natural Frequency: Natural frequency is a term used in physics to describe how quickly an object vibrates when it is set in motion. The number of oscillations made by a system in a given time period without any external force acting on it is referred to as its natural frequency. A natural frequency is a measure of a system's stiffness and mass. In a control system, it is the frequency at which the system oscillates in the absence of any input.
A natural frequency is also known as an undamped natural frequency or a resonance frequency, and it is represented by the symbol [tex]\omega_n[/tex].You can assume the following in the problem. If you have any specific values, kindly provide them.
Learn more about Transfer Function here:
https://brainly.com/question/24241688
#SPJ11
the low-level wind shear alert system (llwas) provides wind data and software process to detect the presence of a
The Low-Level Wind Shear Alert System (LLWAS) provides wind data and software processes to detect the presence of hazardous wind shear.
LLWAS (Low-level windshear alerting systems) is a tool with a system to detect the presence of windshears close to the airport, and will provide warning windshear information automatically if has exceeded its threshold.
It works by collecting data from wind speed and direction sensors located around an airport to provide real-time monitoring of changes in wind direction and speed that can lead to hazardous wind shear events. The data is used to create an alert if hazardous wind shear is detected.
Learn more about LLWAS : https://brainly.com/question/30001468
#SPJ11
Apart from replacement and displament deep foundations,
1. whats a third soloution and
2 method of installation ,
3. advantages, disadvantages
4. how it is connected to the foundation, then describe the role this connection plays resisting forces (e.g. lateral restraint, and others)
Alternative deep foundation: helical piles. Installed with torque, ideal for limited access sites, vibration-free. Resist lateral forces.
What is the explanation for the above response? The third solution for deep foundations is the use of micropiles.Micropiles are typically installed using a drilling rig, and the process involves drilling a small diameter hole (usually less than 30 cm) into the ground and then filling it with a high-strength grout material, followed by the installation of a steel reinforcing element.Advantages of using micropiles include their ability to be installed in low headroom areas, the ability to be installed in difficult soil conditions, and their low noise and vibration during installation. However, their load carrying capacity is typically lower than that of traditional piles, and their installation can be more expensive than other deep foundation solutions.Micropiles are connected to the foundation through a pile cap or a concrete footing, which transfers the load from the structure to the micropiles. The connection between the micropiles and the foundation provides lateral restraint and resists forces such as wind and earthquake loads. The micropiles can also provide uplift resistance, as they are typically installed at an angle to increase their effective length and capacity.Learn more about deep foundations at:
https://brainly.com/question/29341501
#SPJ1
The Mississippi River is on average 20 ft deep and considered one of the widest rivers in the world at around one mile. It is mud-lined with a Manning's roughness coefficient of 0.03. Using a fake slope of 0.0006, what is the river's velocity in ft/s?
Using a fake slοpe οf 0.0006, The Mississippi River mοves at a speed οf rοughly 10.13 feet per secοnd.
The Mississippi River's brοadest pοint is where?The Mississippi River is brοader than 11 miles in Lake Winnibigοshish, which is clοse tο Bena, Minnesοta. The Mississippi shipping rοute's widest navigable part, Lake Pepin, has a channel width οf arοund twο miles.
Q = (1/n) × A × (R²/³) × S¹/²
Tο sοlve fοr velοcity :
V = Q / A
A = depth * width = 20 ft × 5280 ft
= 105,600 ft²
R = A / P
where P is the wetted perimeter οf the channel, which is the length οf the bοundary between the water and the channel bed. Fοr a rectangular channel,
P = 2 × depth + width
= 2 × 20 ft + 5280 ft
= 5320 ft
R = 105,600 ft² / 5320 ft
= 19.81 ft
Nοw we can plug in the values intο the Manning's equatiοn:
Q = (1/0.03) × 105600 ft² × (19.81 ft)²/³ × (0.0006)¹/²
= 1,069,301 ft³/s
Finally, we can calculate the velοcity:
V = Q /
= 1,069,301 ft³/s / 105,600 ft²
= 10.13 ft/s
Learn more about speed :
brainly.com/question/29780075
#SPJ1
if the op amp has a gain bandwidth of 220 khz, what will the bandwidth of the whole amplifier circuit be
The bandwidth of an operational amplifier (op amp) circuit is determined by the gain-bandwidth product (GBP) of the op amp, which is the product of the open-loop gain and the frequency at which the gain drops to 1.
Assuming that the op amp has an ideal gain of infinity (i.e., the open-loop gain is much larger than any closed-loop gain), the GBP is equal to the unity-gain bandwidth of the op amp, which is the frequency at which the gain drops to 1 when the feedback is set to unity gain.
Therefore, if the op amp has a gain-bandwidth of 220 kHz, the bandwidth of the whole amplifier circuit will depend on the closed-loop gain of the circuit.
For a non-inverting amplifier, the closed-loop gain is given by:
A = 1 + (Rf/Rin)
where Rf is the feedback resistance and Rin is the input resistance.
The bandwidth of the circuit can be approximated as:
Bandwidth = GBP / A
Assuming a typical non-inverting amplifier with Rf = 10 kΩ and Rin = 1 kΩ, the closed-loop gain would be:
A = 1 + (10 kΩ / 1 kΩ) = 11
Substituting the values into the formula for bandwidth, we get:
Bandwidth = 220 kHz / 11 = 20 kHz
Therefore, the bandwidth of the whole amplifier circuit would be approximately 20 kHz in this case.
what is the lowest possible frequency of an aliased signal if a 120 khz signal is sampled at 150 khz?
The lowest possible frequency of an aliased signal if a 120 kHz signal is sampled at 150 kHz is 30 kHz.
This is because the highest frequency component of a signal must be less than half the sampling frequency, or Nyquist Frequency. In this case, the Nyquist Frequency is 75 kHz, and 120 kHz is greater than 75 kHz, so it is aliased. The aliased frequency is equal to the difference between the sampling frequency and the highest frequency component, or 150 kHz - 120 kHz = 30 kHz.
Nyquist frequency is a type of sampling frequency used in signal processing which is defined as “half the rate” of a discrete signal processing system. This is the highest frequency that can be encoded for a given sampling rate so that the signal can be reconstructed.
Learn more about frequency : https://brainly.com/question/26146342
#SPJ11
in the context of dynamic person-situation interaction, the main difference between evocation and manipulation is that:
Manipulation involves the intentional control of a situation by a person, whereas evocation is the process through which people elicit responses from others simply by displaying certain behaviors.
Manipulation is a term used in psychology to refer to the intentional control of a situation or environment by a person. It can be used to gain control over others, influence their behavior, or alter their perceptions.
Manipulation can be positive or negative, depending on the intention of the person doing the manipulating. Some forms of manipulation may involve deception, coercion, or exploitation.
On the other hand, evocation is a process through which people elicit responses from others simply by displaying certain behaviors. This is often done unintentionally, without the person being aware that they are having an impact on others.
Unlike manipulation, evocation does not involve intentional control over a situation or environment.
Learn more about manipulation here:
https://brainly.com/question/27154551
#SPJ11
air is compressed steadily and adiabatically from 290k, 90 kpa to 480k, 390 kpa. what is the isentropic efficiency of the compressor? a
The Isentropic efficiency of the compressor Let's consider the given parameters; Initial conditions: T1 = 290 kP1 = 90 kPa Final conditions: T2 = 480 kP2 = 390 kPa The isentropic efficiency of the compressor can be calculated using the following formula:ηs = (h2s - h1) / (h2 - h1)Whereηs = Isentropic efficiency of the compressorh1 = Enthalpy at the inlet of the compressorh2 = Enthalpy at the outlet of the compressorh2s = Isentropic enthalpy at the outlet of the compressor.
Now let's calculate the enthalpies; From the given conditions, we can find out the state point of the air at the inlet of the compressor using the steam tables: At P1 = 90 kPa, T1 = 290 K Using the steam tables, we find out h1 = 315.83 kJ/kg Similarly, we can find out the state point of the air at the outlet of the compressor using the steam tables: At P2 = 390 kPa, T2 = 480 K Using the steam tables, we find out h2 = 421.45 kJ/kg Now, let's calculate the isentropic enthalpy at the outlet of the compressor: Using the steam tables, we can find out the state point of the air at the outlet of the compressor if it were isentropic. At P2 = 390 kPa and S1 = S2Using the steam tables, we find out h2s = 455.41 kJ/kg Substituting these values in the isentropic efficiency formula, we get;ηs = (h2s - h1) / (h2 - h1)ηs = (455.41 - 315.83) / (421.45 - 315.83)ηs = 0.72Thus, the isentropic efficiency of the compressor is 72%.
for more such questions on parameters.
https://brainly.com/question/30380032
#SPJ11
which type of sprinkler system allows immediate and simultaneous discharge of all sprinkler heads? dry-pipe system deluge system pre-action system wet-pipe system
The type of sprinkler system that allows immediate and simultaneous discharge of all sprinkler heads is the deluge system.
In a deluge system, all the sprinkler heads are open and ready to discharge water at all times. The system is activated by a separate fire detection system, such as smoke detectors or heat sensors, which triggers the release of water from all the sprinkler heads at once. This makes deluge systems ideal for high hazard areas where fire can spread quickly, such as chemical storage areas or power plants.
In contrast, wet-pipe systems have water in the pipes at all times and require heat to open individual sprinkler heads, while dry-pipe and pre-action systems use compressed air or other gases to hold water back until a sprinkler head is triggered.
To learn more about sprinkler system refer to:
brainly.com/question/28992367
#SPJ4
A 2500 kVA, 6600 V synchronous turbo alternator is operating at full load and 0.8 pf lagging. This machine has a synchronous reactance per phase is 10.4 ohms and a negligible resistance. Calculate the percent voltage regulation?
The percent voltage regulation of the synchronous turbo alternator is 0.0826%. This indicates the ability of the machine to maintain voltage output under different load conditions.
At full load, the apparent power output of the alternator is 2500 kVA. We can find the real power output by multiplying it by the power factor:
Real power = 2500 kVA x 0.8 = 2000 kW
The current drawn by the alternator can be calculated using the real power and voltage:
Current (I) = Real power (P) / Voltage (V) = 2000 kW / 6600 V = 0.303 A
The voltage drop in the synchronous reactance can be calculated using Ohm's Law:
Voltage drop = Current x Synchronous reactance per phase = 0.303 A x 10.4 ohms = 3.15 V
The percent voltage regulation can be calculated using the following formula:
Percent voltage regulation = (Voltage drop / No-load voltage) x 100
The no-load voltage of the alternator can be calculated using the synchronous EMF equation:
No-load voltage = Line voltage / Sq. root of 3
Line voltage = 6600 V
No-load voltage = 6600 V / Sq. root of 3 = 3814 V
Substituting the values:
Percent voltage regulation = (3.15 V / 3814 V) x 100 = 0.0826 %
Therefore, the percent voltage regulation of the synchronous turbo alternator is 0.0826%.
To practice more questions about voltage regulation:
https://brainly.com/question/14407917
#SPJ11
The key difference between taxi-style services and urban mass transit services is _____
The primary distinction between urban mass transit and taxi-style services is the price for consumers.
The key difference between taxi-style services and urban mass transit services is that taxi-style services offer point-to-point transportation services where passengers can be picked up and dropped off at any location of their choice, while urban mass transit services operate on fixed routes with predetermined stops to serve large numbers of passengers at a time.
Taxi-style services, such as ride-hailing apps like Uber and Lyft, provide on-demand transportation services that can be scheduled through a smartphone application. Passengers are picked up and dropped off at their preferred locations and pay for the service based on the distance traveled or the time spent in the vehicle.
In contrast, urban mass transit services, such as buses and trains, operate on fixed routes with predetermined stops. These services are designed to transport large numbers of people at a time and provide access to key destinations such as downtown areas, business districts, and airports. Passengers typically pay a flat fee or use a pre-purchased ticket or pass to ride these services.
To learn more about taxi-style services visit;
https://brainly.com/question/23936041
#SPJ4
concepts are general ideas you use to organize your experience and, in doing so, bring order and intelligibility to your life. t/f
The given statement "Concepts are general ideas that you use to organize your experience and, in doing so, bring order and intelligibility to your life. " is true because It is important to understand what concept is and how they are useful in our daily life as it helps us organize our experiences and ideas.
Concepts are general ideas that can be used to classify and organize information. They provide structure and coherence to our perceptions and experiences. When we have a concept, it helps us bring order to our experiences and gives us a framework for understanding new information.
By organizing information into categories, we can more easily remember, process, and communicate it. This can help us make sense of the world around us and navigate our experiences in a meaningful way. In conclusion, concepts are important because they help us make sense of our experiences and the world around us. They provide structure and intelligibility to our lives, allowing us to organize and communicate our ideas and experiences more effectively.
So the statement is true.
Learn more about "intelligibility" at: https://brainly.com/question/9944825
#SPJ11
the manganese content of a certain stainless steel is to be verified by an activation measurement. the activity induced in a sample of volume v by neutron capture during a time t is given by
By measuring the activity of a sample over time, the manganese content of stainless steel can be verified.
The manganese content of certain stainless steel can be verified by an activation measurement. Activation measurements measure the activity induced in a sample by neutron capture during a specific time period. Activity is given by the equation A = N0e-λt, where N0 is the initial number of atoms, e is Euler's number (2.718...), λ is the decay constant, and t is time. In this equation, A is the activity at a time t and N0 is the initial number of atoms. The decay constant λ indicates the probability of a neutron capture reaction and is dependent on the material's manganese content.
You can learn more about manganese content at: brainly.com/question/29437774
#SPJ11
this is a longitudinal section through the end of a finger. what is the correct name for the area circled in this virtual slide specimen?
The longitudinal segment through the end of a finger in this virtual slide specimen is known as Hyponychium the tissue located underneath the nail plate.
The hyponychium is the area of skin beneath the free edge of the nail plate, at the distal end of the finger or toe. It is sometimes referred to as the "quick" or the "nail bed seal,"
The hyponychium is an important part of the nail unit and is composed of specialized skin cells that help to support and protect the nail.
The hyponychium plays an important role in protecting the underlying nail bed and fingertip from damage, infection, and other types of trauma. Here are some of the benefits of the hyponychium:
1) Protection: The hyponychium acts as a barrier between the nail bed and the environment, protecting the underlying tissue from injury and infection.
2) Seal: The hyponychium seals the area between the nail plate and the nail bed, preventing dirt, debris, and bacteria from getting underneath the nail and causing infection.
3) Sensation: The hyponychium contains nerve endings that provide sensory feedback to the brain, allowing us to feel pressure, touch, and other sensations
For more such questions on finger
https://brainly.com/question/29891515
#SPJ11
Note- The correct question would be as below
This is a longitudinal section through the end of a finger. What is the correct name for the area circled in this virtual slide specimen?
The input x(t) to a LTI system produces the output y(t)
x(t) = e^-t u(t)
y(t) = e^-3t u(t) Find the frequency response of the system, H(ω). Find the Impulse Response of the system, h(t). Find the differential equation for this system.
The frequency response of the system H(s) is (s + 1) / (s + 3) , the Impulse Response of the system h(t) is δ(t) - 2e^{(-3t)u(t)} and the differential equation for this system δ(t) is h'(t) + 3h(t)
To find the frequency response of the system, H(ω), we can use the Laplace transform:
Y(s) = H(s)X(s)
where X(s) and Y(s) are the Laplace transforms of x(t) and y(t), respectively.
Taking the Laplace transform of x(t):
X(s) = 1 / (s + 1)
Taking the Laplace transform of y(t):
Y(s) = 1 / (s + 3)
Substituting these into the equation above:
H(s) = Y(s) / X(s) = (s + 1) / (s + 3)
To find the impulse response of the system, h(t), we can take the inverse Laplace transform of H(s):
h(t) = L^-1 {H(s)} = L^-1 {(s + 1) / (s + 3)}
Using partial fraction decomposition:
H(s) = (s + 1) / (s + 3) = 1 - 2/(s+3)
Taking the inverse Laplace transform:
h(t) = L^-1 {H(s)} = L^-1 {1} - L^-1 {2/(s+3)}
h(t) = δ(t) - 2e^{(-3t)}u(t)
where δ(t) is the Dirac delta function and u(t) is the unit step function.
To find the differential equation for the system, we can use the fact that the impulse response of an LTI system is the solution to the system's differential equation.
From the above, we have:
h(t) = δ(t) - 2e^(-3t)u(t)
Taking the derivative with respect to t:
dh(t)/dt = -3h(t) + δ'(t)
where δ'(t) is the derivative of the Dirac delta function.
Since δ(t) is zero everywhere except at t=0, its derivative is zero everywhere except at t=0 where it is infinite.
Thus, the differential equation for the system is:
dh(t)/dt + 3h(t) = δ(t)
or equivalently,
h'(t) + 3h(t) = δ(t)
where h'(t) is the derivative of h(t).
To practice more questions about differential equation:
https://brainly.com/question/30417555
#SPJ11
explain the difference in the importance of drafts in green-sand casting versus permanent-mold casting.
In green-sand casting, drafts are essential because they provide a gradual slope in the molds that allows the casting to be released easily.
Drafts are not as important in permanent-mold casting because the mold is generally made of metal and can be more easily broken apart. Drafts can still be used in permanent-mold casting, but they are not as necessary.
Greensand is a mixture of quartz sand, water and bentonite. The sample product used is a 90o elbow measuring 0.5 inches with white cast iron material. The surface roughness was observed by visual observation of the casting results of the two green sand mold compositions.
Learn more about green sand : https://brainly.com/question/29850244
#SPJ11
under ideal conditions (that is, conditions where the hydrostatic pressure is negligible), how high would the fluid rise in the tube
Under ideal conditions, the fluid in a tube will rise to a height equal to the level of the fluid in the reservoir.
This is because the fluid pressure in the tube is equal to the atmospheric pressure and the fluid pressure in the reservoir. When the fluid is released from the reservoir, the atmospheric pressure in the tube causes the fluid to rise to the level of the reservoir.
To explain this phenomenon, we can look at Pascal's Law. Pascal's Law states that when pressure is applied to an enclosed system, it is transmitted equally and undiminished in all directions. In this case, the atmospheric pressure is equal in the reservoir and the tube, so the pressure in both areas is the same.
Therefore, when the fluid is released from the reservoir, the atmospheric pressure in the tube causes the fluid to rise to the same level as the fluid in the reservoir. In other words, the height of the fluid in the tube is equal to the level of the fluid in the reservoir. This is true regardless of the size of the tube or the amount of fluid in the reservoir, as long as there is no external force acting on the system.
You can learn more about Pascal's Law at: brainly.com/question/29875098
#SPJ11
for materials such as aluminum, glass, steel, and concrete, the value of the coefficient of volume expansion is approximately how many times larger than the coefficient of linear expansion?
The coefficient of volume expansion and the coefficient of linear expansion are both thermal properties of a material that describe how its dimensions change in response to changes in temperature.
The coefficient of volume expansion (β) represents the fractional change in volume per degree of temperature change, while the coefficient of linear expansion (α) represents the fractional change in length per degree of temperature change.
For most materials, the coefficient of volume expansion is approximately three times larger than the coefficient of linear expansion. This means that the material's volume will change three times as much as its length for the same change in temperature.
For example, the coefficient of linear expansion for aluminum is around 23.1 × 10⁻⁶ /°C, while its coefficient of volume expansion is around 69 × 10⁻⁶ /°C. Similarly, the coefficient of linear expansion for glass is around 8 × 10⁻⁶ /°C, while its coefficient of volume expansion is around 24 × 10⁻⁶ /°C. The exact values can vary depending on the specific material and its composition, but the relationship between the two coefficients generally holds true.
To learn more about linear expansion refer to:
brainly.com/question/14780533
#SPJ4
what is the ratio of the induced emf in the loop cdbc to the induced emf in the loop cadc; i.e., what is ecdbc ecadc ?
The ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:
ecdbc/ecadc = -dΦ_cdbc/dt / (-dΦ_cadc/dt) = dΦ_cadc/dt / dΦ_cdbc/dt
Let's dive deeper into the details below
The induced EMF is the voltage generated by a changing magnetic field in a coil of wire. In a loop, the induced EMF is proportional to the rate of change of the magnetic flux that is threading the loop. Therefore, in a loop, the induced EMF can be calculated as:
induced EMF = -dΦ/dt, where Φ is the magnetic flux threading the loop.
We can assume that both loops are parallel to the surface and therefore perpendicular to the magnetic field. This means that the magnetic flux threading each loop is proportional to the area of the loop, as follows:
Φ_cadc = B A_cadc and Φ_cdbc = B A_cdbc
Therefore, the ratio of the induced EMF in the loop CDBC to the induced EMF in the loop CADC can be calculated as follows:
ecdbc/ecadc = dΦ_cadc/dt / dΦ_cdbc/dt = (B A_cadc)/dt / (B A_cdbc)/dt = A_cadc / A_cdbc
The answer is the ratio of the areas of the loops.
Learn more about magnetic flux.
brainly.com/question/30858765
#SPJ11
Determine the gauge of the wire needed in circuits that specify power source, wire length, amps, and maximum volt drop.
Part I
Locate the wire-size engineering reference table (Chart 44-2) of your textbook to determine wire gauge when the diameter of the wire is known.
Use the table to determine the wire gauge for each wire diameter shown below. You may need to round the numbers to obtain the correct answer.
d = 2576 inch
d = 0.03196 inch
d = 0.0100 inch
d = 0.1285 inch
d = 0.0508 inch
Using the answers you just obtained, place the wire sizes in order from the smallest gauge to the largest.
Remember: The smaller the wire gauge, the larger the diameter of the wire.
Part II
Using what you’ve learned in Part I and the directions below, determine the recommended wire gauge for the following circuits:
Circuit A. Starter circuit using 5 feet of wire, with a 12 V power supply, and a current of 200 Amps.
Circuit B. Dome light circuit using 14 feet of wire, with a 12 V power supply, and a current of 10 Amps.
Circuit C. A/C blower circuit using 24 feet of wire, with a 14.6 V power supply, and a current of 18 Amps.
Use Ohm’s law (E = IR) to determine the resistance in the wire for each circuit. Remember, Volts = E, and the given current = I. (You can refer back to page 433 in your textbook to find the exact formula you’ll need to use.)
Circuit A: R =
Circuit B: R =
Circuit C: R =
The relationship between the resistance and the circuit’s wire is shown in this formula:
R=4ρπ(Id2)
To determine the diameter of the wire needed for each circuit when you know the resistance and wire length, you would use this formula:
R=4ρπ(Id2) d=IR√×π4ρ
R = resistance
r = 250 ohm/inch
l = length of the wire (inches)
d = cross-sectional area of the wire (in2)
You should substitute the calculated value for R and the given values for r and l and find the value of d for each circuit. (Use π = 3.1416.)
For example, here’s an example for Circuit A:
d=IR√×π4ρ=5.24494×3.14161000=.064
Circuit A: d =
Circuit B: d =
Circuit C: d =
Now, look in the engineering reference table for standard American wire or metric gauges (on page 468 of your textbook) to determine the gauge of wire needed for the circuit.
Circuit A:
Circuit B:
Circuit C:
Answer:
See below.
Explanation:
Part I
Using Chart 44-2 in the textbook, we can determine the wire gauge for each given diameter
For d = 0.2576 inch, the wire gauge is 2 AWG.
For d = 0.03196 inch, the wire gauge is 20 AWG.
For d = 0.0100 inch, the wire gauge is 30 AWG.
For d = 0.1285 inch, the wire gauge is 8 AWG.
For d = 0.0508 inch, the wire gauge is 16 AWG.
Ordering the wire sizes from smallest to largest gauge, we have:
30 AWG < 20 AWG < 16 AWG < 8 AWG < 2 AWG
Part IICircuit A
Using Ohm's law, we can calculate the resistance in the wire:
R = E/I = 12/200 = 0.06 ohms
Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:
d = sqrt(R/(4ρπI)) = sqrt(0.06/(42503.1416*200)) = 0.064 inches
Using the engineering reference table, we can see that the wire gauge needed for Circuit A is 2 AWG.
Circuit B
Using Ohm's law, we can calculate the resistance in the wire:
R = E/I = 12/10 = 1.2 ohms
Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:
d = sqrt(R/(4ρπI)) = sqrt(1.2/(42503.1416*10)) = 0.023 inches
Using the engineering reference table, we can see that the wire gauge needed for Circuit B is 14 AWG.
Circuit C
Using Ohm's law, we can calculate the resistance in the wire:
R = E/I = 14.6/18 = 0.811 ohms
Substituting into the formula R = 4ρπ(Id^2), we can solve for the diameter of the wire:
d = sqrt(R/(4ρπI)) = sqrt(0.811/(42503.1416*18)) = 0.060 inches
Using the engineering reference table, we can see that the wire gauge needed for Circuit C is 4 AWG.
what are the functions of school in computer
Answer:
please make me brainalist and keep smiling dude I hope you will be satisfied with my answer
Explanation:
Computers can be used for online education & research. With the help of the internet, students can find useful information about their projects, assignments and also can take useful help from other researchers as they store & organize their research materials in computers.
The XYZ Company is planning a new product line and a new factory to produce the parts and assemble the final products. The product line will include 13 different models. Annual production of each model is expected to be 1,000 units. Each product will be assembled of 250 components, but 65% of these will be purchased parts (not made in the new factory). There is an average of 8 processing operations required to produce each component, and each processing step takes 30 sec (including an allowance for setup time and part handling). Each final unit of product takes 48 min to assemble. All processing operations are performed at work cells that include a production machine and a human worker. Products are assembled at single workstations consisting of one worker each plus assembly fixtures and tooling. Each work cell and each workstation require 25 m2 of floor space and an additional allowance of 45% must be added to the total production area for aisles, work-in-process storage, shipping and receiving, rest rooms, and other utility space. The factory will operate one shift (the day shift, 2,000 hr/yr). Determine: (a) how many processing and assembly operations, (b) how many workers (direct labor only), and (c) how much total floor space will be required in the plant.
The plant will need to perform 9,100,000 processing and assembly procedures altogether.
What fundamental processing tasks are carried out in a manufacturing facility?Shape operations, property-enhancing operations, and surface processing operations are the three distinct categories of processing operations. By using mechanical force, heat, or other forms and combinations of energy, shaping operations change the work material's geometry.
There are 250 components in each product.
Parts purchased as a percentage equal 65%.
250 - (65% x 250) = 87.5 is the number of components that will be produced in the new facility.
Eight processing steps are needed to manufacture each component.
The new factory's processing procedures per component totaled 8 x 87.5, or 700.
13 x 1000 x (700 + 1) = 9,100,000 is the total number of processing and assembly procedures needed for the 13 different models.
To know more about assembly visit:-
https://brainly.com/question/13557244
#SPJ1
in the lecture titled racial projects, housing projects, and engineering projects, the concept of a new landscape of racially differentiated risk was used to describe what? group of answer choices
The lecture titled "Racial Projects, Housing Projects, and Engineering Projects" discusses the concept of a new landscape of racially differentiated risk. This concept is used to describe how racial projects, such as housing projects and engineering projects, created a new landscape of risk that disproportionately affects people of color.
Racial projects are intentional efforts to use race to shape public policy, for example, through the government-led construction of housing projects or the engineering of waterways to provide better access to clean drinking water. These projects can create both economic and physical divides, increasing the risk of health, educational, and economic disparities that disproportionately affect communities of color.
Housing projects are a form of racial project that is used to construct and maintain certain kinds of housing units. These units are often clustered in segregated communities, where they tend to experience poorer living conditions than other neighborhoods. This can lead to economic insecurity and an increased risk of poor health outcomes.
Engineering projects are another form of racial project that involve the engineering of waterways to provide better access to clean drinking water.
Other options including population, and citizenship are not correct. While these projects are beneficial for many people, they also create risks, such as the potential for hazardous materials to leech into the water, which disproportionately affects people of color.
You can learn more about Racial Projects at: brainly.com/question/30216767
#SPJ11