as a rock sinks deeper and deeper into water of constant density, what happens to the buoyant force on it if it started above the surface of the water?

The homogeneous portion of a mixture that is characterized by uniform properties and capable of being separated by mechanical means is called a phase.

A phase's physical and chemical characteristics can be used to determine whether it is a solid, liquid, or gas. Phase separation can be accomplished mechanically via centrifugation, filtration, or sedimentation.

In several disciplines, including chemistry, biology, and engineering, the ability to separate phases is crucial because it enables the separation and purification of desired components from mixtures. The word "homogeneous" describes a phase in which the components are spread uniformly.

To know about homogeneous

https://brainly.com/question/30583932

#SPJ4

The complete question is

A homogeneous portion of a mixture that is characterized by uniform properties and capable of being separated by mechanical means is called a _____.

product

phase

reactant

solvent

The speed of the 4.00-kg mass when it is 1.00 cm above the point from which it was released is 0.866 m/s.

Using the work-energy theorem, the speed of the 4.00-kg mass when it is 1.00 cm above the point from which it was released can be calculated as follows: First, find the potential energy stored in the spring when the mass is pulled down 2.00 cm.

The potential energy (PE) can be calculated using the formula: PE = 0.5 * k * [tex]x^{2}[/tex], where k is the spring constant (1.00 N/cm) and x is the displacement (2.00 cm).

PE = 0.5 * 1.00 * (2.00[tex])^{2}[/tex] = 2.00 J (joules)

Now, find the potential energy when the mass is 1.00 cm above the release point. The new displacement is 1.00 cm (since it moved 1.00 cm upwards).

PE_new = 0.5 * 1.00 * (1.00[tex])^{2}[/tex] = 0.50 J

The difference in potential energy is the kinetic energy (KE) gained by the mass.

KE = PE - PE_new = 2.00 - 0.50 = 1.50 J

The kinetic energy can be calculated using the formula: KE = 0.5 * m * [tex]V^{2}[/tex], where m is the mass (4.00 kg) and v is the speed. We can rearrange the formula to solve for the speed: v = sqrt(2 * KE / m)

v = ([tex]\sqrt{2 * 1.50 / 4.00}[/tex]) = [tex]\sqrt{0.75}[/tex] = 0.866 m/s

So, the speed of the 4.00-kg mass when it is 1.00 cm above the point from which it was released is 0.866 m/s.

Know more about   potential energy  here:

https://brainly.com/question/21175118

#SPJ11

As a result, electric current flows from top to bottom i.e. downwards in the vertical wire.

When the switch is closed, the current will flow downwards in the vertical wire attached to a power supply and a switch. The wire runs through the center of a plastic stand. This is because the direction of electric current is from higher potential to lower potential.

When the switch is closed, it completes the circuit allowing electric current to flow through the wire. The power supply provides a higher potential at the top of the wire and a lower potential at the bottom of the wire.

Here you can learn more about electric current

https://brainly.com/question/2264542#

#SPJ11  

An action that could cause an involuntary wave pulse to go through this line is the contraction of smooth muscle cells. The type of wave pulse that it would start is a mechanical wave pulse.

An involuntary wave is a wave that is not controlled by conscious will, such as the wave of contraction in a muscle. The involuntary wave is an uncoordinated contraction and relaxation of muscles.

A mechanical wave pulse is a wave that propagates through a medium, such as a solid, liquid, or gas, by the motion of particles in the medium. Mechanical waves require a medium to travel, and they transfer energy from one location to another without transferring matter.

Examples of mechanical waves include sound waves, water waves, and seismic waves.

Therefore, a mechanical wave pulse could be initiated by the contraction of smooth muscle cells can cause an involuntary wave pulse.

To know more about mechanical waves click here:

https://brainly.com/question/3101711

#SPJ11

Answer:

the answer is 71.61°

Explanation:

sorry if im wrong

The evolution of a gas, precipitate formation, color change, temperature change, and state change are significant aspects of chemical reaction.

A chemical reaction occurs when one or more substances completely transform into another one or more substances. It can exhibit one or more characteristics, such as a state change, color change, gas evolution, temperature change, precipitate development, etc. The majority of our energy is produced by chemical reactions. Many different types of materials are tested, identified, and studied using chemical reactions.

Combustion reaction, decomposition reaction, neutralization reaction, redox reaction, precipitation or double-displacement reaction, and synthesis reaction are some of the numerous types of reactions.

To learn more about chemical reactions visit:

brainly.com/question/29039149

#SPJ9

What are the characteristics of chemical reactions?

We can use vector addition to solve this problem. The velocity of the boat relative to the ground is the vector sum of the velocity of the boat relative to the water and the velocity of the water relative to the ground.

The velocity of the boat relative to the water can be found by resolving the given velocity into northward and eastward components:vbw_north =  8.2 cos(35°) = 6.73 m/s (northward) vbw_east = 8.2 sin(35°) = 4.64 m/s (eastward) The velocity of the water relative to the ground is simply 1.9 m/s due east. To find the velocity of the boat relative to the ground, we can use the Pythagorean theorem to combine these two velocity components: vbg^2 = vbw_north^2 + vbw_east^2 + vwater^2vbg = sqrt[(6.73 m/s)^2 +  (4.64 m/s)^2 + (1.9 m/s)^2] = 9.28 m/s Therefore, the magnitude of the boat's velocity relative to the ground is 9.28 m/s.

Learn more about  boat's velocity here:

https://brainly.com/question/12109673

#SPJ4

A long solenoid that has 1 040 turns uniformly distributed over a length of 0.410 m produces a magnetic field of magnitude 1.00 10-4 T at its center.

To calculate the current required in the windings for this to occur, we will use the formula: B = μnI, where B = magnetic field, n = number of turns per unit length, I = current, and μ = permeability of free space.Substituting the given values into the formula, we have:B = μnI1.00 x 10^-4 T = 4π x 10^-7 T m/A x (1040/0.410) x IThe number of turns per unit length is n = 1040/0.410 = 2537.8 turns/m.I = (1.00 x 10^-4)/(4π x 10^-7 x 2537.8)I = 0.781 ATherefore, the current required in the windings for a long solenoid that has 1 040 turns uniformly distributed over a length of 0.410 m that produces a magnetic field of magnitude 1.00 x 10^-4 T at its center is 0.781 A.
To find the current required in the solenoid windings, you can use the formula for the magnetic field at the center of a solenoid: B = μ₀ * n * I, where B is the magnetic field, μ₀ is the permeability of free space (4π × 10⁻⁷ Tm/A), n is the number of turns per unit length, and I is the current.

Learn more about  solenoid here;

https://brainly.com/question/15504705

#SPJ4

Magnetization is the measure of the strength and direction of a material's magnetism. The magnetization of a magnetic material depends on the magnetic state of the material, which can be classified into three main categories: paramagnetic, ferromagnetic, and antiferromagnetic.

Paramagnetic Materials:

Paramagnetic materials have a weak magnetic moment that is aligned with an external magnetic field, and the magnetization of such materials is proportional to the applied magnetic field.

In the absence of an external magnetic field, the magnetization is zero. The magnetization is usually small, and the magnetic moment arises from the presence of unpaired electrons in the material.

Ferromagnetic Materials:

Ferromagnetic materials have a strong magnetic moment that is aligned spontaneously, even in the absence of an external magnetic field. The magnetization arises from the alignment of many atomic magnetic moments, which are typically arranged in domains.

In the presence of an external magnetic field, the domains align and contribute to the overall magnetization. The magnetization of ferromagnetic materials is typically large.

Antiferromagnetic Materials:

Antiferromagnetic materials have a magnetic moment that is aligned in an antiparallel direction. The magnetization of such materials is usually zero because the magnetic moments of adjacent atoms cancel out each other.

In an external magnetic field, the magnetic moments may align in the same direction, leading to a nonzero magnetization.

i) Which state has the largest (smallest) magnetization and why?

Ferromagnetic materials have the largest magnetization because they have a spontaneous magnetization that arises from the alignment of many atomic magnetic moments.

Antiferromagnetic materials have the smallest magnetization because the magnetic moments of adjacent atoms cancel each other.

ii) Which magnetic state (ferromagnetic or paramagnetic) is realized at high (low) temperatures and why?

At high temperatures, thermal fluctuations tend to disrupt the alignment of magnetic moments, leading to a decrease in magnetization. Therefore, paramagnetic materials are typically realized at high temperatures.

At low temperatures, the magnetic moments of ferromagnetic materials tend to align spontaneously, leading to a large magnetization. Therefore, ferromagnetic materials are typically realized at low temperatures.

To learn more about Magnetization here:

https://brainly.com/question/13026686

#SPJ11

A single positively charged ion accelerates through a potential difference of 296 volts and has a mass of 3 x 10-26 kg. The radius of the path of the ion in the magnetic field is 1.27 x 10^-3 meters.

To find the radius of the path of the ion in the magnetic field, we can use the formula:

r = mv / (qB)

where r is the radius of the path, m is the mass of the ion, v is its velocity, q is its charge, and B is the magnetic field strength.

We are given that the ion has a mass of 3 x 10^-26 kg and a charge of +1. The potential difference it is accelerated through is 296 V, which means that it gains kinetic energy equal to qV = (1)(296) = 296 J. We can use the conservation of energy to find the velocity of the ion:

1/2 mv^2 = qV

v = (2qV/m)

= (2(1)(296)/(3 x 10^-26))

= 3.27 x 10^6 m/s

Substituting the given values into the formula for the radius, we get:

r = mv / (qB)

= (3 x 10^-26)(3.27 x 10^6) / (1)(0.79)

= 1.27 x 10^-3 m

To learn more about magnetic fields

https://brainly.com/question/11514007

#SPJ4

There are slightly less than 9,000 J of gravitational potential energy in the system.

The total energy in an isolated system is always conserved. This means that the total energy at the beginning of the process must equal the total energy at the end of the process. The total energy at the beginning is 18,000 J. We know that 6,000 J of this energy has been transformed into kinetic energy and 3,000 J has been transformed into elastic potential energy. So, the remaining energy must be gravitational potential energy.

We can calculate the remaining energy as follows:

Total energy = Kinetic energy + Elastic potential energy + Gravitational potential energy

18,000 J = 6,000 J + 3,000 J + Gravitational potential energy

Gravitational potential energy =  11,000.

To know more about the Potential energy, here

https://brainly.com/question/28031336

#SPJ2

The wheel 1 that rolls down the slope will reach the bottom first.

This is because when a wheel rolls, its kinetic energy is a combination of its translational kinetic energy (due to its linear motion) and its rotational kinetic energy (due to its rotation around its center). When the wheel rolls down the slope, some of its potential energy is converted to translational and rotational kinetic energy. The rolling motion allows the wheel to convert more of its potential energy into translational kinetic energy, which makes it move faster than a wheel that only slides down the slope without rolling.

On the other hand, the wheel that slides down the slope without rolling will only have translational kinetic energy, which means it will move slower than the rolling wheel. The negligible friction on the sliding wheel will not make a significant difference in its speed.

To know more about friction, here

brainly.com/question/24132025

#SPJ4

The changes in kinetic energy of the two blocks are both 160 J.

The changes in kinetic energy of the two blocks can be calculated using the work-energy theorem. The force of 10 N applied to both blocks does the same amount of work on each block, since they both move the same distance of 16 m. The work done on each block can be calculated as:

[tex]W = Fd = (10 N)(16 m) = 160 J[/tex]

The change in kinetic energy of each block can then be calculated as:

Δ[tex]K = W = 160 J[/tex]

Since the initial kinetic energy of both blocks is zero, their final kinetic energies are equal to the work done on them:

[tex]K\ final (5 kg block) = 160 J\\K\ final (20 kg block) = 160 J[/tex]

Therefore, changes in kinetic energy of the two blocks are both 160 J.

To know more about  kinetic energy, here

brainly.com/question/26472013

#SPJ4

For a double-slit configuration where the slit separation is four times the slit width, the number of interference fringes that lie in the central peak of the diffraction pattern is 3.

This is because the number of bright fringes (interference fringes) that lie on either side of the central peak in a double-slit diffraction pattern is given by the equation:

nλ/d

where n is the order of the fringe, λ is the wavelength of the incident light, and d is the distance between the slits.

For the central peak, n is equal to zero, so the equation becomes:

0λ/d = 0

This means that there is no fringe at the center of the diffraction pattern.

However, there will be fringes on either side of the central peak, with the first order of bright fringe occurring at:

nλ/d = 1

where n = 1.

For a double-slit configuration where the slit separation is four times the slit width, the distance between the slits is 4w, where w is the width of each slit.

Therefore, the equation becomes:

nλ/4w = 1

nλ = 4w

This means that the first order of bright fringe will occur at a distance of 4w from the center of the diffraction pattern.

Similarly, the second order of bright fringe will occur at:

nλ/4w = 2n

λ = 8w

This means that the second order of bright fringe will occur at a distance of 8w from the center of the diffraction pattern.

Therefore, there will be a total of three interference fringes (bright fringes) in the central peak of the diffraction pattern.

For more such questions on interference fringes, click on:

https://brainly.com/question/29487127

#SPJ11

The types of particles of sand that would make up the location would be Fine sand and silt. Option a

Sand is a granular material composed of finely divided rock and mineral particles with a particle size range of 0.063 to 2 mm. The properties of sand can vary depending on factors such as the source of the sand, the size and shape of the particles, and the environment in which it is found. However, some general properties of sand include:

Particle size: Sand particles are typically larger than silt and clay particles but smaller than gravel particles. They range in size from 0.063 to 2 mm in diameter.

Texture: Sand has a gritty texture and is often used in abrasive applications, such as sandpaper or sandblasting.

Color: The color of sand can vary depending on the composition of the particles. For example, sand made from quartz crystals is typically white or light-colored, while sand made from iron-rich minerals may be darker in color.

Read more on sand here:https://brainly.com/question/1429841

#SPJ1

No, the police cannot cite you for speeding since you were traveling at the speed limit of 60 mph.

Expecting you kept a steady speed of 60 mph, you went for 36 minutes (9:19 a.m. to 9:55 a.m.) prior to passing the second squad car. During this time, you voyaged a distance of 36 miles (60 miles/hour x 0.6 hours). According to the viewpoint of the primary squad car, you were going at a speed of 60 mph, which is beneath the speed furthest reaches of 65 mph. Thusly, the primary squad car can't refer to you for speeding.

At the point when you passed the second squad car, you had voyaged an all out distance of 42 miles (the distance between the two squad cars). You had been driving for 36 minutes (0.6 hours) and your speed was steady at 60 mph. In this way, your typical speed was 70 mph (42 miles ÷ 0.6 hours). This is over the speed furthest reaches of 65 mph, so the second squad car could refer to you for speeding.

To learn more about speed and time, refer:

https://brainly.com/question/15407119

#SPJ4

The displacement of the block from equilibrium when the elastic potential energy is equal to the kinetic energy is

x =a/sqrt(2).

When the elastic potential energy of the spring-block system is equal to the kinetic energy of the block, the displacement from equilibrium can be found using the conservation of energy principle. At this point, the total mechanical energy remains constant.

Let's denote the displacement from equilibrium as x. The elastic potential energy (PE) of the spring is given by (1/2)kx^2, and the kinetic energy (KE) of the block is given by (1/2)mv^2. Since PE = KE, we have:

(1/2)kx^2 = (1/2)mv^2

We also know that the maximum potential energy occurs when the block is pulled back a distance 'a', which is given by:

PE_max = (1/2)ka^2

Now, using the conservation of energy, we can write the total mechanical energy (E) as:

E = PE + KE = (1/2)kx^2 + (1/2)mv^2 = (1/2)ka^2

Substituting the expression for KE from the PE = KE equation, we get:
(1/2)kx^2 + (1/2)kx^2 = (1/2)ka^2
kx^2 = (1/2)ka^2

Now, solving for the displacement 'x', we find:

x^2 = (1/2)a^2
x = a / sqrt(2)

To learn more about Displacement :

https://brainly.com/question/14422259

#SPJ11

The spring constant of the spring is 114 N/m.

The potential energy stored in the compressed spring is given by:

U = (1/2) k x²

where k is the spring constant and x is the compression of the spring. Plugging in the values, can get:

U = (1/2) k (0.15 m)² = 0.01125 k J

This potential energy is converted into kinetic energy of the BB as it is fired from the gun. The kinetic energy of the BB is given by:

K = (1/2) m v²

where m is the mass of the BB and v is its velocity. Plugging in the values, we get:

K = (1/2) (0.04 kg) (8.0 m/s)^2 = 1.28 J

Since energy is conserved, we can equate the potential and kinetic energies:

U = K

0.01125 k = 1.28 J

Solving for k, we get:

k = 114 N/m

So, the spring constant of the spring is 114 N/m.

To know more about spring constant

https://brainly.com/question/16217337

#SPJ4

Answer:

13.5 mA or 0.0135 A

Explanation:

1.

I=V/R

I=V/RI = 15 V/ 1,000 Ω

I=V/RI = 15 V/ 1,000 Ω

I = 0.015 A or 15 mA (milliamperes)

2.

I=V/R

I = 15 V/ 10,000 Ω

I = 0.0015 A or 1.5 mA (milliamperes)

3.

Therefore, the increase in current when the rheostat is adjusted to 1,000 Ω is:

Al 15 mA - 1.5 mA =

Al = 13.5 mA

So the increase in current is 13.5 mA or 0.0135 A

chatgpt

A student can determine whether a collision between two blocks is elastic or inelastic by examining the motion of the blocks before and after the collision.

In an elastic collision, the kinetic energy of the system is conserved, meaning that the total kinetic energy before the collision is equal to the total kinetic energy after the collision. This results in the blocks bouncing off each other and moving away with different velocities.

In an inelastic collision, some of the kinetic energy is lost as heat, sound, or deformation of the objects involved in the collision. This results in the blocks sticking together after the collision and moving away with the same velocity.

To determine whether the collision is elastic or inelastic, the student can measure the velocity of the blocks before and after the collision using a stopwatch and a ruler. If the velocity of the blocks after the collision is different from the velocity before the collision, then the collision is elastic. If the velocity of the blocks after the collision is the same as the velocity before the collision, then the collision is inelastic.

To learn more about elastic collision

https://brainly.com/question/2356330

#SPJ4

In a first-class lever, the effort force and the load force act on opposite sides of the fulcrum, and the lever arm of each force is the perpendicular distance from the force to the fulcrum. The ideal mechanical advantage (IMA) of the lever is the ratio of the distance from the fulcrum to the effort force and the distance from the fulcrum to the load force.

IMA = distance from fulcrum to effort force / distance from fulcrum to load force

In this case, the distance from the fulcrum to the load force is 4 meters, and the distance from the fulcrum to the effort force is 15 meters. Therefore, the IMA of the lever is:

IMA = 15 m / 4 m = 3.75

The input work (Win) is the product of the effort force and the distance the effort force moves:

Win = effort force x distance moved by effort force

In this case, the effort force is 150 N, and it moves a distance of 15 meters. Therefore, the input work is:

Win = 150 N x 15 m = 2,250 J

The output work (Wout) is the product of the load force and the distance the load force moves:

Wout = load force x distance moved by load force

In this case, the load force is 350 N, and it moves a distance of 4 meters. Therefore, the output work is:

Wout = 350 N x 4 m = 1,400 J

More on 1st class levers can be found here: https://brainly.com/question/18937757

#SPJ1

Answer:

it will become an asteroid because of the gravitational force

A comet would not become an asteroid, meteor, or lose its tail unless it were so massive that its bulk produced additional gravity.

When a comet is large and powerful enough to strike the sun directly, it explodes. The comet is crushed by the sun's atmosphere after accelerating to more than 370 miles per second, creating a magnificent explosion that emits cosmic tidal waves of x-rays and ultraviolet light.

A large comet's impact on Earth would be catastrophic. Large tidal waves, fires, and airborne dust and soot buildup could result, blocking out the majority of sunlight, causing vegetation to die and animals to go hungry.

To know more about gravity visit:-

https://brainly.com/question/14874038

#SPJ1

The acceleration of the car is 90 m/s².

The acceleration of the car can be found using the centripetal acceleration formula:

a = v²/r

where v is the velocity of the car and r is the radius of the curve. Plugging in the values, can get:

a = (30 m/s)² / 10 m = 90 m/s²

So, the acceleration of the car would be 90 m/s².

The force responsible for this acceleration is the centripetal force, which is provided by the friction between the tires and the road. This force acts perpendicular to the direction of motion and is directed towards the center of the curve, causing the car to turn. Without this force, the car would continue moving in a straight line instead of following the curved path.

To know more about acceleration

https://brainly.com/question/28341755

#SPJ4

Answer:v

Both prokaryotic and eukaryotic cells have similar features, like ribosomes, genetic material, a cytoplasm, and plasma membranes. There are two primary types of eukaryotic cells: animal and plant cells.

Explanation:

The movement of air masses across North America from west to east is consistent with global flow of wind over the continent.

The movement of air masses across North America from west to east is consistent with the global flow of wind over the continent. This is due to  general circulation of the Earth's atmosphere, which is driven by differences in temperature and pressure.

At the equator, warm air rises, creating low-pressure zone. As the air rises, it cools and releases moisture, thus creating tropical rainforests. This rising air then moves north and south, where it cools and sinks back to surface, thus creating high-pressure zones. The cool air then flows back toward equator, completing the circulation pattern known as Hadley cell.

In the mid-latitudes, the circulation pattern is more complex, with several cells interacting to create the prevailing westerlies that blow from west to east across North America.

To know more about air mass, refer

https://brainly.com/question/19626802

#SPJ1

When released from a height of 1.60 m, a 1.50 kg block suspended from a light string hits the floor with a speed of 5.06 m/s.

To take care of this issue, we really want to utilize preservation of energy. The underlying possible energy of the block is changed over into active energy as it falls, dismissing any misfortunes because of erosion or air opposition.

To start with, we should track down the underlying expected energy of the block:

U_i = mgh

where

m = 1.50 kg (mass of the block)

g = 9.81 [tex]m/s^2[/tex] (speed increase because of gravity)

h = 1.60 m (range from which the block is delivered)

U_i = (1.50 kg)(9.81 [tex]m/s^2[/tex])(1.60 m) = 23.5 J

Then, we should find the last motor energy of the block not long before it strikes the floor:

K_f = (1/2)[tex]mv^2[/tex]

where

v = speed of the block not long before it strikes the floor

We can utilize protection of energy to relate the underlying likely energy to the last motor energy:

U_i = K_f

Subbing the qualities we viewed as above, we get:

23.5 J = (1/2)(1.50 kg)[tex]v^2[/tex]

Settling for v, we get:

v = sqrt[(2*23.5 J)/(1.50 kg)] = 5.06 m/s

Thusly, the speed of the block not long before it strikes the floor is 5.06 m/s.

To learn more about speed, refer:

https://brainly.com/question/15085648

#SPJ4

Answer:

Vx = 80.0 / 5 = 16 m/s         horizontal speed

2.5 sec up, 2.5 sec down     speed of particle in vertical direction after falling for 2.5 sec

Vy = 2.5 * 9.8 = 24.5 m/s   vertical speed of particle

V = (Vx^2 + Vy^2)^1/2 = (16^2 + 24.5^2)^1/2 = 29.3 m/s

The initial speed of the projectile is 20.0 m/s

To solve for the initial speed of the projectile, we can use the fact that the projectile returns to its original height after 5.0 s of flight. This means that the time it takes for the projectile to reach its maximum height is 2.5 s (half of the total flight time).

Using the kinematic equation for vertical motion, we can find the initial vertical velocity of the projectile at launch:

Δy = v₀t + 0.5at²

where Δy = 0 (since the projectile returns to its original height), t = 2.5 s, a = -9.81 m/s² (acceleration due to gravity), and v₀ is the initial vertical velocity.

Solving for v₀, we get:

v₀ = -0.5at² / t

v₀ = -0.5(-9.81 m/s²)(2.5 s) = 12.26 m/s

Now that we know the initial vertical velocity, we can use the horizontal distance traveled (80.0 m) and the total flight time (5.0 s) to find the initial horizontal velocity:

v = d / t

v = 80.0 m / 5.0 s = 16.0 m/s

Therefore, the initial speed of the projectile is:

v₀i = √(v₀² + v²) = √(12.26² + 16.0²) ≈ 20.0 m/s

To know more about projectile, refer here:
https://brainly.com/question/29761109#
#SPJ11

The effect has this most likely had on agriculture is Option A, "It has expanded the size of the market that a farm can supply produce to" is the correct answer.

What is the agriculture effect?

8The effect of modern transportation technology that allows farm produce to be shipped quickly over long distances is most likely to expand the size of the market that a farm can supply produce to.

This is because modern transportation technology enables farmers to transport their produce over long distances quickly and efficiently, which increases the market reach of their products. As a result, farmers can supply their produce to markets that were previously inaccessible to them, thereby expanding their customer base and potentially increasing their profits.

Therefore, option A, "It has expanded the size of the market that a farm can supply produce to" is the correct answer. Options B, C, and D are not supported by the effects of modern transportation technology on agriculture.

To know more about agriculture, visit:

https://brainly.com/question/891222

#SPJ1

Complete question is: Today, modern transportation technology allows farm produce to be shipped quickly over long distances. The effect has this most likely had on agriculture is Option A, "It has expanded the size of the market that a farm can supply produce to".  

The potential difference across any one of the resistors in a circuit where four 20 ohm resistors are connected in series and the combination is connected to a 20 V emf device is 5 V.

What is a potential difference? A potential difference, also known as voltage, is the difference in electric potential energy between two points in an electric field. It is calculated as the work done per unit charge to move a charge from one point to another in the electric field. It is measured in volts (V).How is the potential difference in a circuit determined?The potential difference in a circuit can be calculated using Ohm's law. According to Ohm's law, the potential difference across a resistor is directly proportional to the current flowing through the resistor and the resistance of the resistor.V = IRwhereV is the potential difference (in volts),I is the current (in amperes), andR is the resistance (in ohms).In the given circuit, the total resistance of the four 20 ohm resistors in series is 80 ohms. The emf of the device is 20 V.Using Ohm's law,V = IR20 = I(80)I = 20/80I = 0.25 AThe current flowing through the circuit is 0.25 A. Since the resistors are connected in series, the current flowing through each resistor is the same.I = V/RI = 5/20I = 0.25 AThe potential difference across any one of the resistors is 5 V.

learn more about   resistors here:

https://brainly.com/question/24297401

#SPJ4