A massless spring hangs from the ceiling with a small object of 100 g attached to its lower end. The object is initially held at rest at a position such that the spring is at its rest length. The object is then released and oscillates up and down, with its lowest position being 5.0 cm below the initial position. The object's speed at 2 cm below the initial position is:
Group of answer choices

2.23 m/s

14 m/s

0.21 m/s

0.45 m/s

At its highest temperature, a space heater has a resistance of 17.5 Ω when it is plugged into a wall outlet that supplies a peak voltage of 176.8 V sinusoidally at 60 Hz . the average power output of the space heater is 888 watts.

The average power output of the space heater can be calculated using the root mean square (RMS) values of the voltage and current. The RMS voltage and current are related to the peak voltage and the resistance of the space heater as follows:

V_RMS = V_peak / sqrt(2)

I_RMS = V_RMS / R

where V_RMS is the RMS voltage, I_RMS is the RMS current, V_peak is the peak voltage, and R is the resistance of the space heater.

Substituting the given values, we get:

V_RMS = 176.8 V / sqrt(2) = 124.8 V

I_RMS = 124.8 V / 17.5 Ω = 7.12 A

The average power output of the space heater is given by:

P_avg = V_RMS * I_RMS * cos(θ)

where cos(θ) is the power factor, which we will assume to be 1 for a resistive load like the space heater.

Substituting the values for V_RMS and I_RMS, we get:

P_avg = 124.8 V * 7.12 A * 1 = 888 W.

Learn more about temperature here:

https://brainly.com/question/11464844

#SPJ1

Since [1 + 2] = [1] + [2], the Velocity of the constant 1 and 2 must be the same. Therefore, both constants have the same SI units.

V is the velocity, d is the distance, and t is the duration in the equation V = d/t. Calculate the object's acceleration by dividing its mass by its force, then multiplying the result by the acceleration's duration.

(b) The units of the constants 1 and 2 must be the same because [12 / 12] = 1. As a result, the SI units for both variables are the same.

(c) The units of the constant 2 must be the same as the units of the constant 1 squared because [2] = [2] / [1]. As a result, the SI units for the constants 1 and 2 differ.

(d) The constant 2 must have radians as its units because the cosine function's input must be dimensionless. It is necessary for the constant 1 to have units that enable the cosine function's units to cancel out. This can be done by assigning the constant 1 units that are reciprocal radians, or radians to the power of -1. As a result, the SI units for the constants 1 and 2 are rad-1 and radians, respectively.

Due to the fact that [(2 / 1) - (2)2] equals [(2 / 1)], The units of the constant 2 must match those of the constant 1 cubed, or [22]. As a result, the SI units for the constants 1 and 2 differ.

To know more about Velocity visit:-

https://brainly.com/question/17127206

#SPJ1

Answer:

B. Frequency

Explanation:

Frequency is measured in the unit Hertz (Hz).

The mass of the counterweight required to balance the 90-kg load is also 90 kg.

To balance the 90-kg load, the moment created by the counterweight s must equal the moment created by the load. The moment created by a force is equal to the force multiplied by the perpendicular distance from the force to the point of rotation. In this case, the point of rotation is the fulcrum and the perpendicular distance is the distance between the fulcrum and the force.

Let's assume that the distance between the fulcrum and the load is d, and the distance between the fulcrum and the counterweight is x. We can then write the equation:

mass of counterweight x distance to fulcrum = mass of load x distance to fulcrum

m_s x x = 90 kg x d

We are given that x = 450 mm (0.45 m). Solving for m_s, we get:

m_s = (90 kg x d) / x

We need to determine the value of d in order to calculate the mass of the counterweight. Since the system is in balance, we know that the sum of the moments created by the load and the counterweight must be zero. That is:

mass of load x distance to fulcrum = mass of counterweight x distance to fulcrum

90 kg x d = m_s x (x + d)

Substituting the expression we derived earlier for m_s, we get:

90 kg x d = [(90 kg x d) / x] x (x + d)

Simplifying this expression by cancelling out the factor of d on both sides, we get:

90 kg = (90 kg / x) x (x + d)

Multiplying both sides by x, we get:

90 kg x = 90 kg x (x + d)

Cancelling out the factor of 90 kg, we get:

x = x + d

Solving for d, we get:

d = x = 450 mm = 0.45 m

Now we can use the equation we derived earlier for m_s to calculate the mass of the counterweight:

m_s = (90 kg x 0.45 m) / 0.45 m = 90 kg.

Learn more about moment here:

https://brainly.com/question/16260427

#SPJ1

(9) None of the options listed in the question are correct as a risk assessment approach to environmental hazards.

(10) House debt is not a direct effect of housing on health (option D)

A risk assessment approach to environmental hazards aims to take into account all of the following factors, including the health outcome, inherent danger, quantity of exposure, and route of exposure. Therefore, none of the options listed in the question are correct as all of them should be considered in a risk assessment approach to environmental hazards.

10. While housing affordability and financial stress related to housing can indirectly affect health, they are not a direct effect of housing itself on health.

The other options are direct effects of housing on health:

A. Proximity to services and facilities, such as healthcare, education, and transportation, can affect health outcomes.

B. Materials effects of housing, such as ventilation, insulation, and building materials, can directly affect indoor air quality and physical health.

C. Insecure housing, such as homelessness or living in overcrowded or unsafe conditions, can lead to physical and mental health problems.

Learn more about risk assessment here: https://brainly.com/question/29671743

#SPJ1

Answer:

What are the best flowers? (My opinion)

Explanation:

You're welcome.

Answer:

Tulips,

Lilies,

Lotuses on my opinion...

Answer:

Explanation:

since weight and force both are forces we can simply use the equation

                            F=ma

here ,

  m=mass=9.00kg

  a=acceleration=6.00m/s^2

             So,

                  F=W=54N

For this workout I did squats. Squats may aid in weight loss because they burn calories. Moreover, they reduce the possibility of knee and ankle injuries.

When performing squats, your legs should feel fatigued. Lower back ache is a sign that you're likely doing the workout wrong. This shows that your lower back muscles are working harder than your glutes and quadriceps since they are taking the load. Pay attention to how you squat.

It doesn't matter where it is—a living room, office, stairwell, park, or closet—as long as there are a few feet available. The only thing you need is your body weight.

In some instances, it is acceptable to squat without a spotter. The environment and resources you have at your disposal, though, are everything. The safest choice is to use a power rack or squat stand with adjustable safety pins, arms, or straps.

To know more about the exercise visit:

https://brainly.com/question/19787142

#SPJ1

The required escape velocity from the asteroid in km/s and mph is 2.0 km/s and 4478 mph, respectively.

According to analyses of orbital statistics, asteroids of 10 km in size can strike the planet every 100 My or so, which is consistent with the theory that we were struck by an object of this size 65 My ago.

Part A: Escape velocity is the bare minimum speed at which an object can break out of an astronomical body's gravitational influence. The following provides the escape velocity formula:

v = √((2GM)/r)

Where, G = gravitational constant M = mass of the astronomical body r = radius of the astronomical body

Now, let's substitute the given values to find the escape velocity from the asteroid.

Given, Diameter of the asteroid, d = 10 km

So, radius of the asteroid, r = d/2 = 5 km = 5 × 10³ m

Density of the asteroid, ρ = 3000 kg/m³

Mass of the asteroid, M = ρ × volume of the asteroid= ρ × (4/3)πr³= 3000 × (4/3) × π × (5 × 10³)³= 6.54 × 10¹¹ kg

Gravitational constant, G = 6.67 × 10⁻¹¹ Nm²/kg²

Putting all these values in the escape velocity formula, v = √((2GM)/r)= √((2 × 6.67 × 10⁻¹¹ × 6.54 × 10¹¹)/5 × 10³)= 2.0 km/s

Therefore, the escape velocity from the asteroid is 2.0 km/s.

Part B : Now, let's convert the escape velocity from km/s to mph.1 km = 0.621371192 milesSo, v in mph = 2.0 km/s × (0.621371192 miles/km) × (3600 s/hour)= 4478 mph

Therefore, the escape velocity from the asteroid is 4478 mph (rounded to three significant figures).

Hence, the required escape velocity from the asteroid in km/s and mph is 2.0 km/s and 4478 mph, respectively.

To know more about escape velocity visit:-

https://brainly.com/question/31149165

#SPJ1

Question:

You are standing on the surface of a spherical asteroid 10 km in diameter, of density 3000 kg/m3.

Part A

Calculate the escape velocity from the asteroid in km/s.

Express your answer in kilometers per second using two significant figures.

Calculate the escape velocity from the asteroid in mph.

Express your answer in miles per hour using three significant figures

We can infer that item A is not composed of the same material as object B since its specific heat capacity is higher than object B's. As the specific heat capacities differ, we cannot assume that they are the same.

The amount of heat needed to increase the warmth of one unit of mass of a substance by one degrees Celsius must be compared between two things in order to ascertain if they are made of the same material. The compounds are probably the same if the heat capacity capacities are the same. The following equation can be used to determine how much heat energy is needed to raise an object's temperature:

Q = mcΔT

Where Q is the heat received or released, m is the object's mass, c is the material's specific heat capacity, and T is the temperature change.

Let's figure out how much heat energy is needed to raise item A's temperature by one degree Celsius:

Q A = mcΔT

Q A equals 6 kg x 2,310 J/(kg°C) x 1°C.

Q A = 13,860 J/°C

Let's now determine how much heat energy is needed to raise item B's temperature by 1 degree Centigrade:

Q B = mcΔT

Q B is equal to 4.6 kg, 1,771 J/(kg°C), and 1°C.

Q B = 8,146.6 J/°C

To Know more about Mass Visit:

brainly.com/question/19694949

#SPJ1

Answer:

130.43g

Explanation:

First, we need to calculate the heat lost by the tea when it cools down from 33.3°C to 31.8°C. We can use the formula Q = mcΔT, where Q is the heat lost, m is the mass of the tea, c is the specific heat capacity of water, and ΔT is the change in temperature.

The mass of the tea is given as 187g and the specific heat capacity of water is 4186 J/kg·°C. The change in temperature is (33.3 - 31.8)°C = 1.5°C.

So, the heat lost by the tea is: Q = (187g) * (4186 J/kg·°C) * (1.5°C) = 1174.05 J

This heat is gained by the ice, causing it to melt and warm up to 0°C. The heat required to melt ice is given by Q = mL, where m is the mass of ice melted and L is the latent heat of fusion of water.

The latent heat of fusion of water is 334 kJ/kg. So, we can calculate the mass of ice melted as: m = Q / L = (1174.05 J) / (334 kJ/kg) = 0.0035 kg = 3.5g

However, not all of the ice will melt. Some of it will remain as ice and some will become water at 0°C.

Let’s say that x grams of ice melts completely and becomes water at 0°C. The remaining (133 - x) grams of ice will stay as ice.

The heat required to melt x grams of ice is: Q1 = x * L

The heat required to warm up x grams of water from 0°C to 31.8°C is: Q2 = x * c * (31.8 - 0)

The total heat gained by the ice and water is: Q = Q1 + Q2

Substituting the values we get: 1174.05 J = x * L + x * c * (31.8 - 0)

Solving for x, we get: x = 1174.05 J / (L + c * (31.8 - 0)) = 2.57g

Therefore, out of the initial 133g of ice, only 2.57g melts completely and becomes water at 0°C.

The remaining mass of ice in the jar is: 133g - 2.57g = 130.43g

So, at the time at which the temperature of the tea is 31.8°C, there are approximately 130.43g of ice remaining in the jar.

The TV's efficiency rating is 5.56%.

An isolated system has a constant total energy. Energy cannot be generated or destroyed; it can only be transformed from one form to another or transferred between systems. When all energy sources are considered, the overall energy of an isolated system is constant.

Efficiency is equal to (useful energy output/total energy intake) multiplied by 100%.

Useful energy output = light energy output + sound energy output

= 10 kJ + 30 kJ

= 40 kJ

Total energy input = electrical energy input

= 720 kJ

Substituting these values into the efficiency formula, we get:

Efficiency = (40 kJ / 720 kJ) x 100%

= 0.0556 x 100%

= 5.56%

To know more about efficiency rating visit:-

https://brainly.com/question/11553375

#SPJ9

B) The relationship between revolutions per second AND average time should be an inverse relationship: (as one increases the other decreases) is incorrect.

This is incorrect because, as the length of the string increases, the average time for 10 revolutions should increase as well. This is because the bobber has to travel farther as the string gets longer, and so it takes longer to finish 10 revolutions. Therefore, the relationship between revolutions per second and average time is not inverse; instead, it is a direct relationship. As the length of the string increases, the average revolutions per second should increase, and the average time should decrease. This means that the relationship between the two is actually a direct relationship  as one increases, the other increases as well.

learn more about revolutions Refer:brainly.com/question/25591420

#SPJ1

Answer:

Use the formula to determine the contact area of each tire with the road.

Area divided by force yields pressure, as the equation suggests.

The weight of the car, which is 1500 kg, exerts a force on an area where pressure is at 2.2 x 10^5 Pa.

Supported by all four tires, we must first determine the total force.

Weight of car is 1500 kg multiplied by 9.8m/s^2 equals =14700 N, also known as total force.

Equally sharing the load, four tires are responsible for supporting the vehicle.

Each tire carries a force that equals the total force divided by 4, which is equivalent to 3675 N as calculated from a total force of 14700 N.

Each tire's contact area with the road can now be calculated.

3675 N divided by 2.2 x 10^5 Pa equals the area. This area can also be described as force divided by pressure.

Approximately 16.7 cm^2 or 1.67 x 10^-2 m^2 is the designated area.

The contact area between the road and each tire measures exactly 16.7 cm^2.

The period of the ocean waves hitting the beach at a rate of 35 Hz is 0.0286 seconds.

Frequency and period are inversely related in wave motion. The frequency of a wave is the number of complete cycles (or wave crests) that pass a point in a given time period, while the period is the time it takes for one complete cycle to occur. The period can be calculated by dividing the inverse of the frequency.

Ocean waves form due to the transfer of energy from wind to water. Factors that affect the characteristics of ocean waves include wind speed and duration, the distance over which the wind blows (known as fetch), and the depth and shape of the seafloor.

The size and shape of ocean waves can also be affected by tides, currents, and the presence of nearby land masses.

To know more about wave motion,visit:

https://brainly.com/question/12512349

#SPJ1

The direction of the north pole of a compass needle represents the direction of magnetic field lines. Magnetic field lines originate from the north pole of magnet and terminate at south pole. Hence, the correct compass will be A.

A plotting compass is also known as a magnetic compass. It aligns itself with the magnetic field of magnet, with north-seeking end of the compass pointing towards the south pole of the magnet and the south-seeking end pointing towards the north pole of the magnet.

So, to determine which plotting compass is pointing in the correct direction, you would need to observe the direction in which the north-seeking end of the compass is pointing and compare it to the direction in which the south pole of the bar magnet is located. If the north-seeking end of the compass is pointing towards the south pole of the magnet, then the compass is pointing in the correct direction.

To know more about compass, refer

https://brainly.com/question/924374

#SPJ1

Therefore, the component of vector C is -4.125m in the x direction and 6.125m in the y direction.

Physical objects called vectors need both magnitude and direction. Scalars include things like height, mass, area, and volume. Vectors can take the forms of motion, velocity, and acceleration.

In order to find vector C, we can commence by rearranging the equation 2A - B - 4C = 0:

2A - B - 4C = 0

2A - B = 4C

C = (2A - B)/4

We can now determine the elements of vectors A and B:

Vector A: Ax = -3m, Ay = 10m

Vector B: Bx = 8.5m, By = -3.5m

When we enter these numbers into the vector C equation, we obtain:

Cx = (2Ax - Bx)/4 = (2(-3m) - 8.5m)/4 = -4.125m

Cy = (2Ay - By)/4 = (2(10m) - (-3.5m))/4 = 6.125m

To know more about vector visit:-

https://brainly.com/question/29708786

#SPJ9

The formula for the force required to stop the automobile is F = m x a, where m = 1200 kg and F = 1200 x (-12.5) N = - 15000 N.

As a car brakes, the rotating wheels create friction inside the wheel assemblies, bringing the vehicle to a stop. The kinetic energy of the automobile is lost as heat in the braking components due to this friction force, which slows the spinning of the wheels.

The automobile can come to a stop with any force higher than zero. The only difference is that it will take longer and cover a bigger distance before stopping.

Unless a force acts on a body, it stays at rest or moves in a straight path at a constant speed.

learn more about kinetic energy

https://brainly.com/question/25959744

#SPJ1

Explanation:

speed = wavelength * frequency

         =   3 m  *  12 /s  = 36 m/s

The two properties of particles which make up a substance that affect its internal energy are:

A. Motion and position

The internal energy of a substance depends on the kinetic energy (motion) and potential energy (position) of its constituent particles. The kinetic energy of the particles determines the temperature of the substance, while the potential energy depends on the intermolecular forces between the particles.

Therefore, option A is the correct answer.

Based on the information, a guide on how to fill out your fitness log is given.

Date: Write the current date.

Warm-up: Indicate what type of warm-up exercise you did before the actual activity. For example, you may have stretched or walked briskly for five minutes before starting the actual exercise.

Cool-down: Indicate what type of cool-down exercise you did after the actual activity. For example, you may have stretched or walked slowly for five minutes after completing the actual exercise.

Type of Activity: Choose whether the exercise you did is cardiovascular, muscular, or flexibility training.

Description of Activity and Time: Provide a brief description of the exercise you did and how long you did it. For instance, if you did a low-impact floor drill for 30 minutes, write "Low-impact floor drill for 30 minutes."

Intensity Level: Choose whether the exercise was moderate or vigorous.

Total Time: Write the total time you spent doing the exercise, including warm-up and cool-down. For example, if you spent five minutes warming up, 30 minutes doing the actual exercise, and five minutes cooling down, write "40 minutes" as the total time.

Remember to update your fitness log regularly to monitor your progress and achieve your fitness goals.

Learn more about fitness on

https://brainly.com/question/13490156

#SPJ1

elevator of mass 550 kg and a counter weight of 700 kg lifts 23 tired 80-kg students to the 7th floor of a dormitory 30 meters off the ground in 12 seconds. then the power required to lift the 23 students to the 7th floor is 41,948.85 W or 56.22 hp.

To solve this problem, we need to use the formula for power, which is:

Power = Work/Time

We can find the work done by the elevator by using the formula:

Work = Force x Distance

The force required to lift the elevator and the counterweight is:

Force = (mass of elevator + mass of counterweight + mass of students) x g

where g is the acceleration due to gravity, which is approximately 9.81 m/s².

So the force required is:

Force = (550 + 700 + 23 x 80) x 9.81

= 16,779.54 N

The distance traveled by the elevator is 30 meters, so the work done by the elevator is:

Work = Force x Distance

= 16,779.54 x 30

= 503,386.2 J

Now, we can calculate the power required:

Power = Work/Time

= 503,386.2/12

= 41,948.85 W

To convert watts to horsepower, we can use the conversion factor 1 hp = 746 W. Therefore, the power required is:

Power = 41,948.85/746

= 56.22 hp

Learn more about power here:

https://brainly.com/question/29575208

#SPJ1

For solving this problem,we have to apply Newton’s law of gravitation which defines the magnitude of the force between two objects.

Gravitational Force -

[tex]\:\:\:\:\:\:\:\sf \underline{\boxed{\sf{F=G\times \dfrac{ \: m_1 \: m_2}{r^2}}}}[/tex]

Where:-

As per question, we are given -

Now that required values are given, so we can substitute the values into the formula and solve for Force of gravity:-

[tex] \:\:\:\:\:\:\:\longrightarrow \sf Force_{(gravity) }= 6.7\times 10^{-11} \times \dfrac{3.5\times 6.4\times 10^{23}}{(5.6\times 10^{10})^2}\\[/tex]

[tex] \:\:\:\:\:\:\:\longrightarrow \sf Force_{(gravity) }=6.7\times 10^{-11} \times \dfrac{1400.46}{23172.08}\\[/tex]

[tex] \:\:\:\:\:\:\:\longrightarrow \sf Force_{(gravity) }=6.7\times 10^{-11} \times 0.06\\[/tex]

[tex] \:\:\:\:\:\:\:\longrightarrow \sf \underline{Force_{(gravity) } = 4.02\times 10^{-12}\:N}\\[/tex]

Based on the given fundamental frequency of 7 Hz, it is likely that the harmonic is a multiple of the fundamental frequency.

Harmonics are integer multiples of the fundamental frequency and can be calculated using the formula: f(n) = n * f(1), where f(n) is the frequency of the nth harmonic, and f(1) is the frequency of the fundamental harmonic.

Therefore, the frequency at which this harmonic is created will depend on the harmonic number. For example, the second harmonic would have a frequency of 14 Hz (2 * 7 Hz), the third harmonic would have a frequency of 21 Hz (3 * 7 Hz), and so on. Without knowing the harmonic number, it is not possible to determine the frequency at which this harmonic is created.

To know more about harmonic number, visit:

https://brainly.com/question/12320829

#SPJ1

Answer:

a. Spalling

Answer:

To calculate the total force on Earth due to Venus, Jupiter, and Saturn, we need to use the formula for gravitational force: F = G * (m1 * m2) / r^2 where F is the gravitational force, G is the gravitational constant, m1 and m2 are the masses of the two objects, and r is the distance between them. First, we need to convert the distances to meters: dV = 108 million km * 1000 m/km = 1.08 x 10^11 m dJ = 150 million km * 1000 m/km = 1.5 x 10^11 m dSat = 778 million km * 1000 m/km = 7.78 x 10^11 m Next, we can calculate the forces due to each planet: FV =

Spectroscopy has much in common with the cosmological concept of redshift and blueshift.

Spectroscopy is the study of the interaction between matter and electromagnetic radiation, and it is commonly used to study the properties of stars and galaxies.

Redshift and blueshift, on the other hand, are phenomena that occur when light is emitted from an object that is moving away or towards an observer, respectively. These concepts are commonly used in cosmology to study the expansion of the universe and the motion of galaxies.

Spectroscopy can be used to measure the redshift or blueshift of light emitted from distant objects, providing valuable information about their distance, velocity, and composition.

learn about Spectroscopy here https://brainly.com/question/28457917

#SPJ1

the correct answer is A. The force would be one-fourth the original force.

According to Coulomb's law, the force between two charged particles is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.

The mathematical expression for Coulomb's law is:

F = k * q1 * q2 / [tex]r^2[/tex]

where F is the force, k is the Coulomb constant, q1 and q2 are the charges of the particles, and r is the distance between them.

In this case, the force is given as -0.5 N, which means that the charges must be of opposite signs. Let's assume that the charged sphere has a positive charge, so the test particle must have a negative charge. The distance between them is initially 1 meter.

Plugging in the given values into Coulomb's law, we get:

-0.5 N = k * q_sphere * q_particle / [tex](1 m)^2[/tex]

where q_sphere is the charge of the sphere and q_particle is the charge of the test particle.

If we double the distance between the particles to 2 meters, then the new force can be calculated using the same equation:

F' = k * q_sphere * q_particle / ([tex]2 m)^2[/tex]

To determine how the new force F' relates to the original force F, we can take the ratio of the two equations:

F' / F = (k * q_sphere * q_particle / [tex](2 m)^2\\[/tex]) / (k * q_sphere * q_particle / (1 [tex]m)^2[/tex])

= (1/4)

Learn more about Coulomb's here:

https://brainly.com/question/12498766

#SPJ1

Answer: A

Explanation: the correct answer is A, The force would be one-fourth the original force.

Sam put in -845 J of work to halt it. Sam had to exert effort in the direction counter to the way the boat was moving, as indicated by the negative sign, which denotes that he did negative work.

One can compute the initial kinetic energy as follows:

KEi is equal to (1/2)mv2, where m is the combined mass of the boat and its riders (1000 kg), and v is the boat's initial speed (1.3 m/s).

KEi = (1/2)(1000 kg)(1.3 m/s), which equals 845 J.

The boat is brought to a stop, and as a result, its terminal velocity and kinetic energy are both zero:

KEf = 0 J

Sam put forth the following effort to stop the boat: W = 0 J - 845 J

To learn more about work done visit:

brainly.com/question/13662169

#SPJ1